51
绿联nas排查硬盘故障
乐果 发表于 2025 年 02 月 01 日 标签：openwrt
家里的绿联 nas 好久没用，假期在家捣腾时发现启动不了，便求助了绿联官方技术远程协助排查原因。
故障表现：插两块硬盘时 nas 启动不了，插任意一块硬盘 nas 正常启动。
整个操作过程记录一下，以便以后自己排查这方面的故障方便。
Microsoft Windows [版本 10.0.26100.2894]
(c) Microsoft Corporation。保留所有权利。
C:\Users\Administrator>ssh -p 922 root@192.168.2.150
The authenticity of host '[192.168.2.150]:922 ([192.168.2.150]:922)' can't be established.
ED25519 key fingerprint is SHA256:deZq0pajrwYROo2JUFN12vXqfyZFZlRU2xos3112lC0.
This key is not known by any other names.
Are you sure you want to continue connecting (yes/no/[fingerprint])? yes
Warning: Permanently added '[192.168.2.150]:922' (ED25519) to the list of known hosts.
root@192.168.2.150's password:
BusyBox v1.28.3 () built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
UGOS 18.06-SNAPSHOT,
-----------------------------------------------------
如上说明绿联的 nas 系统是基于 openwrt 改造的。
下面则是官方技术远程排查硬盘的命令了，如下：
root@UGREEN-38CA:~# lsblk
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
sda 8:0 0 5.5T 0 disk
└─sda1 8:1 0 5.5T 0 part
└─md0 9:0 0 5.5T 0 raid1 /mnt/md0
mmcblk0 179:0 0 7.3G 0 disk
├─mmcblk0p1 179:1 0 1G 0 part /rom
└─mmcblk0p2 179:2 0 5.2G 0 part /overlay
mmcblk0boot0 179:8 0 4M 1 disk
mmcblk0boot1 179:16 0 4M 1 disk
mmcblk0rpmb 179:24 0 512K 0 disk
root@UGREEN-38CA:~# smartctl -ai /dev/sda
smartctl 7.2 2020-12-30 r5155 [aarch64-linux-4.9.119] (localbuild)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: ST6000NM0024-1HT17Z
Serial Number: Z4D3EQ84
LU WWN Device Id: 5 000c50 0877e5030
Add. Product Id: DELL(tm)
Firmware Version: MA29
User Capacity: 6,001,175,126,016 bytes [6.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-3 (minor revision not indicated)
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sat Feb 1 09:25:22 2025 CST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 90) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 626) minutes.
Conveyance self-test routine
recommended polling time: ( 3) minutes.
SCT capabilities: (0x50bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x010f 077 064 --- Pre-fail Always - 50644912
3 Spin_Up_Time 0x0103 087 085 --- Pre-fail Always - 0
4 Start_Stop_Count 0x0032 099 099 --- Old_age Always - 1032
5 Reallocated_Sector_Ct 0x0133 100 100 --- Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 078 077 --- Pre-fail Always - 83074841
9 Power_On_Hours 0x0032 091 091 --- Old_age Always - 8257
10 Spin_Retry_Count 0x0013 100 100 --- Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 --- Old_age Always - 56
184 End-to-End_Error 0x0032 100 100 --- Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 --- Old_age Always - 0
188 Command_Timeout 0x0032 100 099 --- Old_age Always - 8590065666
189 High_Fly_Writes 0x003a 100 100 --- Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 065 047 --- Old_age Always - 35 (Min/Max 34/35)
191 G-Sense_Error_Rate 0x0032 100 100 --- Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 --- Old_age Always - 31
193 Load_Cycle_Count 0x0032 100 100 --- Old_age Always - 273
194 Temperature_Celsius 0x0022 035 053 --- Old_age Always - 35 (0 11 0 0 0)
195 Hardware_ECC_Recovered 0x001a 008 006 --- Old_age Always - 50644912
196 Reallocated_Event_Count 0x0032 000 000 --- Old_age Always - 0
197 Current_Pending_Sector 0x0012 100 100 --- Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 --- Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 --- Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 --- Old_age Offline - 414 (186 99 0)
241 Total_LBAs_Written 0x0000 100 253 --- Old_age Offline - 3936432071
242 Total_LBAs_Read 0x0000 100 253 --- Old_age Offline - 9203453322
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 8257 -
# 2 Short offline Completed without error 00% 8002 -
# 3 Short offline Completed without error 00% 7530 -
# 4 Short offline Completed without error 00% 3659 -
# 5 Short offline Completed without error 00% 3587 -
# 6 Short offline Completed without error 00% 3515 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
root@UGREEN-38CA:~# dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.9.119 (ugreen@jenkins-ugos) (gcc version 8.2.0 (OpenWrt GCC 8.2.0 ) ) #0 SMP PREEMPT Mon Apr 8 13:55:47 2024
[ 0.000000] Boot CPU: AArch64 Processor [410fd034]
[ 0.000000] DT: logo_start_addr 0x30000000, size 0x900000
[ 0.000000] DT: free_logo_reserved_region 0
[ 0.000000] DT: saving_section_page_table 0
[ 0.000000] earlycon: uart8250 at MMIO32 0x0000000098007800 (options '')
[ 0.000000] bootconsole [uart8250] enabled
[ 0.000000] rsvmem_remap_setup 234, not remap common@0 now
[ 0.000000] rsvmem_remap_setup 234, not remap ringbuf@0 now
[ 0.000000] rsvmem_remap_setup 234, not remap rbus@0 now
[ 0.000000] cma: size 0x0000000002000000, base 0x0000000000000000, fixed(0)
[ 0.000000] cma: Reserved 32 MiB at 0x000000007e000000
[ 0.000000] On node 0 totalpages: 523776
[ 0.000000] DMA zone: 8192 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 523776 pages, LIFO batch:31
[ 0.000000] percpu: Embedded 22 pages/cpu @ffffffc07df5f000 s52376 r8192 d29544 u90112
[ 0.000000] pcpu-alloc: s52376 r8192 d29544 u90112 alloc=22*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: enabling workaround for ARM erratum 845719
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 515584
[ 0.000000] Kernel command line: earlycon=uart8250,mmio32,0x98007800 console=ttyS0,115200 U-boot=2015.07-45f6c71 (May 12 2021 - 16:47:00) init=/etc/init root=/dev/mmcblk0p1 rootfstype=squashfs overlay=/dev/mmcblk0p2 overlayfs=ext4 rootwait loglevel=8
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Memory: 1553200K/2095104K available (7678K kernel code, 1058K rwdata, 4152K rodata, 3392K init, 415K bss, 509136K reserved, 32768K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB)
[ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB)
[ 0.000000] .text : 0xffffff8008280000 - 0xffffff8008a00000 ( 7680 KB)
[ 0.000000] .rodata : 0xffffff8008a00000 - 0xffffff8008e20000 ( 4224 KB)
[ 0.000000] .init : 0xffffff8008e20000 - 0xffffff8009170000 ( 3392 KB)
[ 0.000000] .data : 0xffffff8009170000 - 0xffffff8009278808 ( 1059 KB)
[ 0.000000] .bss : 0xffffff8009278808 - 0xffffff80092e046c ( 416 KB)
[ 0.000000] fixed : 0xffffffbefe7fb000 - 0xffffffbefec00000 ( 4116 KB)
[ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB)
[ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum)
[ 0.000000] 0xffffffbf00000000 - 0xffffffbf02000000 ( 32 MB actual)
[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc080000000 ( 2048 MB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] CONFIG_RCU_FANOUT set to non-default value of 32
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 27.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x63a1e71a3, max_idle_ns: 440795203123 ns
[ 0.000005] sched_clock: 56 bits at 27MHz, resolution 37ns, wraps every 4398046511093ns
[ 0.009093] [RTK-TIMER0] set mode: shutdown
[ 0.013803] [RTK-TIMER0] clocksource 0 register HZ
[ 0.019195] clocksource: rtk_timer0_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 70787423951 ns
[ 0.030788] [RTK-TIMER1] clocksource 1 register HZ
[ 0.036179] clocksource: rtk_timer1_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 70787423951 ns
[ 0.047961] rmem_count: 4
[ 0.051882]
[ 0.053551] rsvmem_remap 143, rmem->name common@0
[ 0.059824] rsvmem_remap 151, type rsvmem-remap
[ 0.065900] rsvmem_remap 163, ioremap(1f000,1000)
[ 0.072173] rsvmem_remap 175, remap addr ffffff800800c000
[ 0.079227] rsvmem_remap 184, save_remap_name common
[ 0.085791] rsvmem_remap 203, save rpc_common_base
[ 0.092157] rsvmem_remap 216, init common@0/common done
[ 0.099011]
[ 0.100679] rsvmem_remap 143, rmem->name ringbuf@0
[ 0.107046] rsvmem_remap 151, type rsvmem-remap
[ 0.113118] rsvmem_remap 163, ioremap(1ffe000,4000)
[ 0.119587] rsvmem_remap 175, remap addr ffffff8008010000
[ 0.126642] rsvmem_remap 184, save_remap_name ringbuf
[ 0.133301] rsvmem_remap 210, save rpc_ringbuf_base
[ 0.139765] rsvmem_remap 216, init ringbuf@0/ringbuf done
[ 0.146813]
[ 0.148482] rsvmem_remap 143, rmem->name ramoops@0
[ 0.154849] rsvmem_remap 151, type ramoops
[ 0.160432] rsvmem_remap 154, value is not match
[ 0.166601]
[ 0.168270] rsvmem_remap 143, rmem->name rbus@0
[ 0.174344] rsvmem_remap 151, type rsvmem-remap
[ 0.180420] rsvmem_remap 163, ioremap(98000000,200000)
[ 0.187182] rsvmem_remap 175, remap addr ffffff8009400000
[ 0.194234] rsvmem_remap 184, save_remap_name rbus
[ 0.200601] rsvmem_remap 188, save rbus_addr
[ 0.206383] rsvmem_remap 195, set rtk_rbus_barrier_flag to 1
[ 0.213727] rsvmem_remap 216, init rbus@0/rbus done
[ 0.220588] Console: colour dummy device 80x25
[ 0.225622] Calibrating delay loop (skipped), value calculated using timer frequency.. 54.00 BogoMIPS (lpj=108000)
[ 0.237305] pid_max: default: 32768 minimum: 301
[ 0.242703] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.250271] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.258989] ftrace: allocating 29761 entries in 117 pages
[ 0.323794] sched-energy: CPU device node has no sched-energy-costs
[ 0.330902] Invalid sched_group_energy for CPU0
[ 0.336015] CPU0: update cpu_capacity 1024
[ 0.340666] ASID allocator initialised with 32768 entries
[ 0.427118] Detected VIPT I-cache on CPU1
[ 0.427171] Invalid sched_group_energy for CPU1
[ 0.427175] CPU1: update cpu_capacity 1024
[ 0.427178] CPU1: Booted secondary processor [410fd034]
[ 0.459183] Detected VIPT I-cache on CPU2
[ 0.459215] Invalid sched_group_energy for CPU2
[ 0.459218] CPU2: update cpu_capacity 1024
[ 0.459222] CPU2: Booted secondary processor [410fd034]
[ 0.491276] Detected VIPT I-cache on CPU3
[ 0.491308] Invalid sched_group_energy for CPU3
[ 0.491312] CPU3: update cpu_capacity 1024
[ 0.491315] CPU3: Booted secondary processor [410fd034]
[ 0.491394] Brought up 4 CPUs
[ 0.555126] SMP: Total of 4 processors activated.
[ 0.560434] CPU features: detected feature: 32-bit EL0 Support
[ 0.567017] CPU features: detected feature: Kernel page table isolation (KPTI)
[ 0.578087] CPU: All CPU(s) started at EL2
[ 0.582729] alternatives: patching kernel code
[ 0.587947] Invalid sched_group_energy for CPU3
[ 0.593063] Invalid sched_group_energy for Cluster3
[ 0.598563] Invalid sched_group_energy for CPU2
[ 0.603674] Invalid sched_group_energy for Cluster2
[ 0.609174] Invalid sched_group_energy for CPU1
[ 0.614286] Invalid sched_group_energy for Cluster1
[ 0.619788] Invalid sched_group_energy for CPU0
[ 0.624899] Invalid sched_group_energy for Cluster0
[ 0.630929] devtmpfs: initialized
[ 0.646146] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.657157] futex hash table entries: 1024 (order: 5, 131072 bytes)
[ 0.665691] pinctrl core: initialized pinctrl subsystem
[ 0.672295] NET: Registered protocol family 16
[ 0.689353] cpuidle: using governor ladder
[ 0.710012] cpuidle: using governor menu
[ 0.714854] vdso: 2 pages (1 code @ ffffff8008a06000, 1 data @ ffffff8009174000)
[ 0.723211] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.731554] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.738784] rst-control : base ffffff8008060600, offset 0x40
[ 0.745187] ****** rtk_lockapi_init 620, chip: id=0x00000000, revision=0x00030000
[ 0.753630] ****** rtk_lockapi_init 627, bypass mode
[ 0.759789] pstore: using zlib compression
[ 0.764424] pstore: Registered ramoops as persistent store backend
[ 0.771402] ramoops: attached 0x200000@0x22000000, ecc: 0/0
[ 0.778280] rtk-mmio 98000000.mmio: use hw semaphore
[ 0.783988] rtk-cgc 9800000c.clk-en: initialized
[ 0.789457] rtk-cgc 98000010.clk-en: initialized
[ 0.794807] rtk-cgc 98000450.clk-en: initialized
[ 0.800171] rtk-mmio 98007088.mmio: use hw semaphore
[ 0.805855] rtk-cgc 9800708c.clk-en: initialized
[ 0.811200] rtk-rtd129x-cc 98000000.clock-controller: use mmio regmap
[ 0.818716] rtk-rtd129x-cc 98000000.clock-controller: initialized
[ 0.825732] rtk-reset 98000000.soft-reset: use mmio regmap
[ 0.831931] rtk-reset 98000000.soft-reset: initialized
[ 0.837861] rtk-reset 98000000.shadow-soft-reset: use mmio regmap
[ 0.844747] rtk-reset 98000000.shadow-soft-reset: initialized
[ 0.851359] rtk-reset 98000004.soft-reset: use mmio regmap
[ 0.857558] rtk-reset 98000004.soft-reset: initialized
[ 0.863484] rtk-reset 98000008.soft-reset: use mmio regmap
[ 0.869684] rtk-reset 98000008.soft-reset: initialized
[ 0.875614] rtk-reset 98000050.soft-reset: use mmio regmap
[ 0.881814] rtk-reset 98000050.soft-reset: initialized
[ 0.887745] rtk-reset 98007088.soft-reset: use mmio regmap
[ 0.893944] rtk-reset 98007088.soft-reset: initialized
[ 0.899872] rtk-reset 98000000.async-soft-reset: use mmio regmap
[ 0.906658] rtk-reset 98000000.async-soft-reset: initialized
[ 0.913176] rtk-reset 98000004.async-soft-reset: use mmio regmap
[ 0.919963] rtk-reset 98000004.async-soft-reset: initialized
[ 0.926659] rtk-rtd129x-power 98000000.power-controller: initialized
[ 0.933987] [PINCTRL] driver init
[ 0.940286] [PINCTRL] init done
[ 0.946309] [RTK_DCSYS_DBG] DC_EC_CTRL(0x98008300) = 7000000
[ 0.952711] [RTK_DCSYS_DBG] initialized
[ 0.962359] [GPIO] No default gpio need to set
[ 0.970870] [RTK_SB2_DBG] sb2_dbg_probe
[ 0.975262] [RTK_SB2_DBG] info 0x30000
[ 0.979494] [RTK_SB2_DBG] use smc 0
[ 1.004537] ACPI: Interpreter disabled.
[ 1.008921] [RTD129x_PM] Initial Power Management Driver
[ 1.015285] [RTD129x_PM] wakeup-gpio Cnt: en(2) act(2) list(2)
[ 1.021883] [RTD129x_PM] wakeup-gpio[0] States is disable!
[ 1.027875] (en:0 act:1 gpio:115)
[ 1.031748] [RTD129x_PM] wakeup-gpio[1] Successful registration!
[ 1.038330] (en:1 act:0 gpio:134)
[ 1.042163] [RTD129x_PM] gpio-output-change Cnt: en(0) act(0) list(-2)
[ 1.049528] [RTD129x_PM] Wakeup Flags Set Default : 0x2c
[ 1.055522] [RTD129x_PM] as system-power-controller
[ 1.061107] rtk-usb-manager 98000000.rtk_usb_power_manager: ENTER rtk_usb_manager_probe
[ 1.070175] rtk-usb-manager 98000000.rtk_usb_power_manager: parse_gpio_setting get power-gpio (id=102) OK
[ 1.080989] rtk-usb-manager 98000000.rtk_usb_power_manager: parse_gpio_setting get power-gpio (id=132) OK
[ 1.091802] rtk-usb-manager 98000000.rtk_usb_power_manager: parse_gpio_setting get power-gpio (id=133) OK
[ 1.102618] mac_node: rtk_dwc3_drd status is okay
[ 1.107926] type_c_node: rtk_dwc3_drd_type_c status is okay
[ 1.114221] rtk-usb-manager 98000000.rtk_usb_power_manager: __of_parse_port_gpio_mapping port0 mapping gpio_num=102
[ 1.126008] mac_node: rtk_dwc3_u2host status is okay
[ 1.131616] rtk-usb-manager 98000000.rtk_usb_power_manager: __of_parse_port_gpio_mapping port1 mapping gpio_num=132
[ 1.143406] mac_node: ehci status is okay
[ 1.147930] slave_mac_node: ohci status is okay
[ 1.153047] rtk-usb-manager 98000000.rtk_usb_power_manager: __of_parse_port_gpio_mapping port2 mapping gpio_num=132
[ 1.164836] mac_node: rtk_dwc3_u3host status is okay
[ 1.170445] rtk-usb-manager 98000000.rtk_usb_power_manager: __of_parse_port_gpio_mapping port3 mapping gpio_num=133
[ 1.182221] rtk_usb_soc_init START (drivers/soc/realtek/rtd129x/rtk_usb.c)
[ 1.190018] rtk_usb_iso_power_ctrl power_on ([0x98007fb0=0x0f000073)
[ 1.197190] set usb_power_domain/p3 on
[ 1.201425] set power_domain on ([0x98007fb0]=0x0f000073)
[ 1.208073] rtk-usb-manager 98000000.rtk_usb_power_manager: Realtek USB init OK
[ 1.216350] rtk-usb-manager 98000000.rtk_usb_power_manager: __gpio_on_off to set power off by gpio (id=102) OK
[ 1.227659] rtk-usb-manager 98000000.rtk_usb_power_manager: __gpio_on_off to set power off by gpio (id=132) OK
[ 1.238963] rtk-usb-manager 98000000.rtk_usb_power_manager: __gpio_on_off to set power off by gpio (id=133) OK
[ 1.250348] rtk-usb-manager 98000000.rtk_usb_power_manager: create_debug_files
[ 1.258547] rtk-usb-manager 98000000.rtk_usb_power_manager: rtk_usb_manager_probe OK (take 196 ms)
[ 1.269046] SCSI subsystem initialized
[ 1.273315] libata version 3.00 loaded.
[ 1.277735] usbcore: registered new interface driver usbfs
[ 1.283973] usbcore: registered new interface driver hub
[ 1.290043] usbcore: registered new device driver usb
[ 1.296177] rtk-efuse 98017000.efuse: initialized
[ 1.301682] Advanced Linux Sound Architecture Driver Initialized.
[ 1.309601] clocksource: Switched to clocksource arch_sys_counter
[ 1.345314] VFS: Disk quotas dquot_6.6.0
[ 1.349817] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.357731] FS-Cache: Loaded
[ 1.361036] pnp: PnP ACPI: disabled
[ 1.365261] drivers/soc/realtek/common/rtk_ion_of.c rtk_ion_probe
[ 1.373144] drivers/soc/realtek/common/rtk_ion_of.c rtk_ion_probe nr_heaps:5
[ 1.385035] rtk_ion_probe: adding heap Audio of type 8 with 2600000@800000 (type:GEN_POOL)
[ 1.530219] rtk_ion_probe: adding heap Media of type 7 with 7e000000@2000000 (type:CMA_POOL)
[ 1.540732] rtk_ion_probe: adding heap Media of type 7 with 12000000@d500000 (type:GEN_POOL)
[ 1.551241] rtk_ion_probe: adding heap Media of type 7 with 2e00000@d200000 (type:GEN_POOL)
[ 1.569728] NET: Registered protocol family 2
[ 1.575192] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 1.583503] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[ 1.591263] TCP: Hash tables configured (established 16384 bind 16384)
[ 1.598679] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 1.605512] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 1.612981] NET: Registered protocol family 1
[ 1.618234] RPC: Registered named UNIX socket transport module.
[ 1.624922] RPC: Registered udp transport module.
[ 1.630231] RPC: Registered tcp transport module.
[ 1.635539] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.642811] PCI: CLS 0 bytes, default 128
[ 1.647797] Failed to device reset: -2
[ 1.652334] Failed to device reset: -2
[ 1.656744] Failed to device reset: -2
[ 1.661165] Failed to device reset: -2
[ 1.665675] Failed to device reset: -2
[ 1.670078] Failed to device reset: -2
[ 1.678125] Crashlog allocated RAM at address 0x3f00000
[ 1.684242] workingset: timestamp_bits=46 max_order=19 bucket_order=0
[ 1.692354] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.699191] FS-Cache: Netfs 'nfs' registered for caching
[ 1.705393] NFS: Registering the id_resolver key type
[ 1.711113] Key type id_resolver registered
[ 1.715843] Key type id_legacy registered
[ 1.720385] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.728294] Key type cifs.idmap registered
[ 1.734580] NET: Registered protocol family 38
[ 1.739659] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 1.748018] io scheduler noop registered
[ 1.752448] io scheduler deadline registered
[ 1.757354] io scheduler cfq registered (default)
[ 1.762919] phy-rtk-sata 9803ff00.sata_phy: can't find rx table
[ 1.769719] phy-rtk-sata 9803ff00.sata_phy: can't find rx table
[ 1.776732] [RTK_PWM] rtd1295_pwm_probe - hwpwm=(0) enable=(0) duty_rate=(5) clksrc_div=(1) clkout_div=(255)---
[ 1.788330] [RTK_PWM] rtd1295_pwm_probe - defualt output frequence = 26367Hz ---
[ 1.796879] [RTK_PWM] rtd1295_pwm_probe - hwpwm=(1) enable=(1) duty_rate=(50) clksrc_div=(1) clkout_div=(255)---
[ 1.808563] [RTK_PWM] rtd1295_pwm_probe - defualt output frequence = 26367Hz ---
[ 1.817112] [RTK_PWM] rtd1295_pwm_probe - hwpwm=(2) enable=(0) duty_rate=(50) clksrc_div=(1) clkout_div=(255)---
[ 1.828794] [RTK_PWM] rtd1295_pwm_probe - defualt output frequence = 26367Hz ---
[ 1.837342] [RTK_PWM] rtd1295_pwm_probe - hwpwm=(3) enable=(0) duty_rate=(50) clksrc_div=(1) clkout_div=(255)---
[ 1.849018] [RTK_PWM] rtd1295_pwm_probe - defualt output frequence = 26367Hz ---
[ 1.857683] 980070d0.pwm.0: failed to get pinctrl: -19
[ 1.863626] 980070d0.pwm.1: failed to get pinctrl: -19
[ 1.869565] 980070d0.pwm.2: failed to get pinctrl: -19
[ 1.876838] misc rtk_lockapi: registered.
[ 1.881386] [PUWRAP] begin pu_init
[ 1.885226] [PUWRAP] end pu_init result=0x0
[ 1.890050] [PUWRAP] pu_probe
[ 1.893432] [PUWRAP] success to probe pu wrapper device with USE_ION_ALLOCATOR
[ 1.901769] [RTK_VE1] vpu_probe
[ 1.905324] [RTK_VE1] vpu base address get from DTB physical base addr=0x98040000, virtual base=0xffffff8008270000, size=0x8000
[ 1.918418] [RTK_VE1] res.start:0x98007000, bonding_value:0x0
[ 1.925005] [RTK_VE1] s_ve1_irq:22 want to register ve1_irq_handler
[ 1.932130] [RTK_VE1] s_ve2_irq:23 want to register ve2_irq_handler
[ 1.939230] [RTK_VE1] success to probe vpu device with non reserved video memory
[ 1.947786] [RTK_VE3] base address get from DTB physical base addr=0x98048000, virtual base=0xffffff80092e8000, size=0x4000(actually=0x424)
[ 1.962070] [RTK_VE3] get clock controller s_ve3_clk=0xffffffc07ac52800
[ 1.969543] ve3_pctrl_on
[ 1.981622] [RTK_VE3] Get cti: 0x13
[ 1.985546] [RTK_VE3] dec kernel module
[ 1.989880] [RTK_VE3] Init single core at 0x 98048000 IRQ=24
[ 1.996956] [RTK_VE3] core[0] has HEVC
[ 2.001187] [RTK_VE3] core[0] has VP9
[ 2.005321] [RTK_VE3] core[0] has PP
[ 2.009541] [RTK_VE3] module inserted. Major = 0
[ 2.014765] ve3_pctrl_off
[ 2.017789] memalloc: Linear Memory Allocator
[ 2.022934] [RTK_JPU] jpu_probe
[ 2.026506] [RTK_JPU] jpu base address get from DTB physical base addr=0x9803e000, virtual base=0xffffff80081c9000, size=0x1000
[ 2.039591] [RTK_JPU] get clock controller s_jpu_clk=0xffffffc07ac52000
[ 2.047090] [RTK_JPU] s_jpu_irq:21 want to register jpu_irq_handler
[ 2.054194] [RTK_JPU] success to probe jpu device with non reserved video memory
[ 2.062612] [RTK_JPU] jpu_init
[ 2.066063] [RTK_JPU] end jpu_init result=0x0
[ 2.071329] [RTK_RPC] rpc driver initial begin
[ 2.076465] [RTK_RPC]rpc is not paused & suspended
[ 2.083779] [RTK_RPC] rpc_int_base:ffffff80081e9104
[ 2.089295] [RTK_RPC] acpu_irq:27
[ 2.093062] [RTK_RPC] rpc driver initial done
[ 2.098172] [RTK MCP] MCP driver initial begin.
[ 2.103303] [RTK MCP] MCP Base: 0xffffff80081f1000
[ 2.108712] [RTK MCP] TP Base: 0xffffff80081f9000
[ 2.263128] [RTK MCP] MCP driver initial done.
[ 2.268722] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 2.277173] console [ttyS0] disabled
[ 2.281276] 98007800.serial0: ttyS0 at MMIO 0x98007800 (irq = 194, base_baud = 1687500) is a 16550A
[ 2.291563] console [ttyS0] enabled
[ 2.299072] bootconsole [uart8250] disabled
[ 2.308427] [RTK_SB2_DBG] sb2 get int 0x00000002 from SB2_INV_INTSTAT
[ 2.308576] 9801b200.serial1: ttyS1 at MMIO 0x9801b200 (irq = 163, base_baud = 27000000) is a 16550A
[ 2.324374] [RTK_SB2_DBG] Invalid access issued by SCPU
[ 2.330614] [RTK_SB2_DBG] Invalid address is 0x9801b2f8
[ 2.336854] [RTK_SB2_DBG] Timeout threshold(0x0000004d)
[ 2.342211] [RTK_SB2_DBG] sb2 get int 0x00000002 from SB2_INV_INTSTAT
[ 2.348810] [RTK_SB2_DBG] Invalid access issued by SCPU
[ 2.355050] [RTK_SB2_DBG] Invalid address is 0x9801b210
[ 2.361289] [RTK_SB2_DBG] Timeout threshold(0x0000004d)
[ 2.375762] brd: module loaded
[ 2.380906] g2227 0-0012: g2227 rev219
[ 2.389930] g2227-regulator g2227-regulator: initialized
[ 2.395403] g2227 0-0012: initialized
[ 2.400243] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x1111
[ 2.406065] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x5111
[ 2.411879] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x9111
[ 2.417691] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x336a0511
[ 2.423858] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x336a4511
[ 2.430025] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x336a8511
[ 2.436192] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0xe0700111
[ 2.442359] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0xe05c4111
[ 2.448526] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0xe04a8111
[ 2.454693] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x150611
[ 2.460682] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x154611
[ 2.466672] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x158611
[ 2.472661] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0xc6000a11
[ 2.478828] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0xc6004a11
[ 2.484995] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0xc6008a11
[ 2.491163] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x70000211
[ 2.497329] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x70004211
[ 2.503497] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x70008211
[ 2.509663] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0xc6600a11
[ 2.515829] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0xc6604a11
[ 2.521996] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0xc6608a11
[ 2.528162] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x20041911
[ 2.534329] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x20045911
[ 2.540495] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x20049911
[ 2.546662] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x94aa2011
[ 2.552830] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x94aa6011
[ 2.558996] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x94aaa011
[ 2.565163] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x17171511
[ 2.571329] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x17175511
[ 2.577495] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x17179511
[ 2.583662] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x7701611
[ 2.589740] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x7705611
[ 2.595817] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x7709611
[ 2.601896] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x40002a11
[ 2.608062] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x40006a11
[ 2.614229] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x4000aa11
[ 2.620395] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x29001011
[ 2.626562] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x29005011
[ 2.632729] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x29009011
[ 2.638895] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x40000c11
[ 2.645063] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x40004c11
[ 2.651230] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x40008c11
[ 2.657397] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x271711
[ 2.663386] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x275711
[ 2.669376] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x279711
[ 2.675364] phy-rtk-sata 9803ff00.sata_phy: phy0 txdrv 0x94a72011
[ 2.681620] phy-rtk-sata 9803ff00.sata_phy: phy0 txdrv 0x94a76011
[ 2.687875] phy-rtk-sata 9803ff00.sata_phy: phy0 txdrv 0x94a7a011
[ 2.694139] phy-rtk-sata 9803ff00.sata_phy: phy0 txdrv 0x587a2111
[ 2.700395] phy-rtk-sata 9803ff00.sata_phy: phy0 txdrv 0x587a6111
[ 2.706653] phy-rtk-sata 9803ff00.sata_phy: phy0 txdrv 0x587aa111
[ 2.712909] phy-rtk-sata 9803ff00.sata_phy: phy0 rxsense 0x42100911
[ 2.719343] phy-rtk-sata 9803ff00.sata_phy: phy0 rxsense 0x42104911
[ 2.725778] phy-rtk-sata 9803ff00.sata_phy: phy0 rxsense 0x42108911
[ 2.732212] phy-rtk-sata 9803ff00.sata_phy: phy0 rxsense 0x276f0311
[ 2.738646] phy-rtk-sata 9803ff00.sata_phy: phy0 rxsense 0x276d4311
[ 2.745080] phy-rtk-sata 9803ff00.sata_phy: phy0 rxsense 0x276d8311
[ 2.751545] phy-rtk-sata 9803ff00.sata_phy: init phy0 OK
[ 2.757001] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x1111
[ 2.762813] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x5111
[ 2.768623] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x9111
[ 2.774434] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x336a0511
[ 2.780601] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x336a4511
[ 2.786768] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x336a8511
[ 2.792935] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0xe0700111
[ 2.799101] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0xe05c4111
[ 2.805269] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0xe04a8111
[ 2.811435] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x150611
[ 2.817425] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x154611
[ 2.823413] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x158611
[ 2.829402] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0xc6000a11
[ 2.835569] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0xc6004a11
[ 2.841736] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0xc6008a11
[ 2.847903] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x70000211
[ 2.854069] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x70004211
[ 2.860235] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x70008211
[ 2.866402] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0xc6600a11
[ 2.872570] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0xc6604a11
[ 2.878736] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0xc6608a11
[ 2.884903] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x20041911
[ 2.891069] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x20045911
[ 2.897235] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x20049911
[ 2.903403] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x94aa2011
[ 2.909569] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x94aa6011
[ 2.915736] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x94aaa011
[ 2.921902] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x17171511
[ 2.928069] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x17175511
[ 2.934235] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x17179511
[ 2.940401] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x7701611
[ 2.946480] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x7705611
[ 2.952557] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x7709611
[ 2.958635] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x40002a11
[ 2.964801] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x40006a11
[ 2.970968] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x4000aa11
[ 2.977134] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x29001011
[ 2.983301] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x29005011
[ 2.989468] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x29009011
[ 2.995635] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x40000c11
[ 3.001801] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x40004c11
[ 3.007968] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x40008c11
[ 3.014134] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x271711
[ 3.020123] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x275711
[ 3.026112] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x279711
[ 3.032102] phy-rtk-sata 9803ff00.sata_phy: phy1 txdrv 0x94a72011
[ 3.038357] phy-rtk-sata 9803ff00.sata_phy: phy1 txdrv 0x94a76011
[ 3.044614] phy-rtk-sata 9803ff00.sata_phy: phy1 txdrv 0x94a7a011
[ 3.050869] phy-rtk-sata 9803ff00.sata_phy: phy1 txdrv 0x587a2111
[ 3.057124] phy-rtk-sata 9803ff00.sata_phy: phy1 txdrv 0x587a6111
[ 3.063380] phy-rtk-sata 9803ff00.sata_phy: phy1 txdrv 0x587aa111
[ 3.069635] phy-rtk-sata 9803ff00.sata_phy: phy1 rxsense 0x42100911
[ 3.076069] phy-rtk-sata 9803ff00.sata_phy: phy1 rxsense 0x42104911
[ 3.082503] phy-rtk-sata 9803ff00.sata_phy: phy1 rxsense 0x42108911
[ 3.088936] phy-rtk-sata 9803ff00.sata_phy: phy1 rxsense 0x276f0311
[ 3.095377] phy-rtk-sata 9803ff00.sata_phy: phy1 rxsense 0x276d4311
[ 3.101812] phy-rtk-sata 9803ff00.sata_phy: phy1 rxsense 0x276d8311
[ 3.108278] phy-rtk-sata 9803ff00.sata_phy: init phy1 OK
[ 3.113936] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[ 3.122171] r8169 Gigabit Ethernet driver 2.6.0LK-NAPI loaded
[ 3.138388] r8169 98016000.gmac eth0: RTL8168g/8111g at 0xffffff8008241000, XID 10900800 IRQ 17
[ 3.147319] r8169 98016000.gmac eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[ 3.156233] [Ethernet] Watch link status change.
[ 3.156610] rtk-uio 98000000.rbus: initialized
[ 3.156801] rtk-uio 9801b000.refclk: initialized
[ 3.161099] rtk-se 9800c000.se: irq=15
[ 3.161108] rtk-se 9800c000.se: phys:0x000000009800c000 virt:0xffffff8008259000 size:0x0000000000001000 type:1 name:SE reg space
[ 3.161116] rtk-se 9800c000.se: phys:0x000000007e040000 virt:0xffffff800826e000 size:0x0000000000001000 type:1 name:SE driver data
[ 3.161124] rtk-se 9800c000.se: phys:0x000000007e048000 virt:0xffffff8009386000 size:0x0000000000008000 type:1 name:SE command queue
[ 3.161370] rtk-se 9800c000.se: [SE] Engine[0] Ctrl:00000001 Base:7e048000 ReadPtr:7e048000 WritePtr:7e048000 Limit:7e04c000
[ 3.161379] rtk-se 9800c000.se: [SE] Engine[1] Ctrl:00000001 Base:7e04c000 ReadPtr:7e04c000 WritePtr:7e04c000 Limit:7e050000
[ 3.161385] rtk-se 9800c000.se: shared mode
[ 3.161391] rtk-se 9800c000.se: initialized
[ 3.161698] rtk-md 9800b000.md: irq=14
[ 3.161707] rtk-md 9800b000.md: phys:0x000000009800b000 virt:0xffffff8008279000 size:0x0000000000001000 type:1 name:MD reg space
[ 3.161715] rtk-md 9800b000.md: phys:0x000000007e041000 virt:0xffffff800827b000 size:0x0000000000001000 type:1 name:MD driver data
[ 3.161723] rtk-md 9800b000.md: phys:0x000000007e044000 virt:0xffffff800938f000 size:0x0000000000004000 type:1 name:MD command queue
[ 3.161957] rtk-md 9800b000.md: [MD] Engine[0] Ctrl:00000005 Base:7e044000 ReadPtr:7e044000 WritePtr:7e044000 Limit:7e048000
[ 3.161964] rtk-md 9800b000.md: shared mode
[ 3.161968] rtk-md 9800b000.md: initialized
[ 3.162183] rtk-usb-phy-rle0599 98013824.usb_phy_rle0599: rtk_usb_rle0599_phy_probe: Chip 1296 revision is b01
[ 3.162234] rtk-usb-phy-rle0599 98013824.usb_phy_rle0599: Probe RTK USB 2.0 RLE0599 PHY
[ 3.162484] rtk-usb2phy 98028280.dwc3_drd_usb2phy: rtk_usb2phy_probe: Chip 1296 revision is b01
[ 3.162532] rtk-usb2phy 98028280.dwc3_drd_usb2phy: drivers/usb/phy/phy-rtk-usb2.c Probe RTK USB 2.0 PHY
[ 3.162579] rtk-usb2phy 98031280.dwc3_u2host_usb2phy: rtk_usb2phy_probe: Chip 1296 revision is b01
[ 3.162629] rtk-usb2phy 98031280.dwc3_u2host_usb2phy: drivers/usb/phy/phy-rtk-usb2.c Probe RTK USB 2.0 PHY
[ 3.162688] rtk-usb2phy 981f8280.dwc3_u3host_usb2phy: rtk_usb2phy_probe: Chip 1296 revision is b01
[ 3.162731] rtk-usb2phy 981f8280.dwc3_u3host_usb2phy: drivers/usb/phy/phy-rtk-usb2.c Probe RTK USB 2.0 PHY
[ 3.162990] rtk-usb3phy 98013210.dwc3_drd_usb3phy: rtk_usb3phy_probe: Chip 1296 revision is b01
[ 3.163014] rtk-usb3phy 98013210.dwc3_drd_usb3phy: rtk_usb3phy_probe load phy_data_revA parameter
[ 3.163044] rtk-usb3phy 98013210.dwc3_drd_usb3phy: drivers/usb/phy/phy-rtk-usb3.c Probe RTK USB 3.0 PHY
[ 3.163103] rtk-usb3phy 98013e10.dwc3_u3host_usb3phy: rtk_usb3phy_probe: Chip 1296 revision is b01
[ 3.163126] rtk-usb3phy 98013e10.dwc3_u3host_usb3phy: rtk_usb3phy_probe load phy_data_revA parameter
[ 3.163154] rtk-usb3phy 98013e10.dwc3_u3host_usb3phy: drivers/usb/phy/phy-rtk-usb3.c Probe RTK USB 3.0 PHY
[ 3.163846] rtk-dwc3 98013200.rtk_dwc3_drd: Probe Realtek-SoC USB DWC3 Host Controller
[ 3.164128] rtk-usb-manager 98000000.rtk_usb_power_manager: rtk_usb_manager_schedule_work for 98013200.rtk_dwc3_drd
[ 3.164146] rtk-dwc3 98013200.rtk_dwc3_drd: dwc3_rtk_probe ok! (take 0 ms)
[ 3.164155] rtk-dwc3 98013200.rtk_dwc3_drd: dwc3_rtk_probe_work Start ...
[ 3.164183] rtk-dwc3 98013c00.rtk_dwc3_u2host: Probe Realtek-SoC USB DWC3 Host Controller
[ 3.164426] rtk-usb-manager 98000000.rtk_usb_power_manager: rtk_usb_manager_schedule_work for 98013c00.rtk_dwc3_u2host
[ 3.164444] rtk-dwc3 98013c00.rtk_dwc3_u2host: dwc3_rtk_probe ok! (take 0 ms)
[ 3.164492] dwc3 98020000.dwc3_drd: rtk dwc3 fixed dwc3 globals register start address 0xffffff80093d8100
[ 3.164501] rtk-dwc3 98013e00.rtk_dwc3_u3host: Probe Realtek-SoC USB DWC3 Host Controller
[ 3.164655] rtk-usb2phy 98028280.dwc3_drd_usb2phy: rtk_usb2_phy_init Init RTK USB 2.0 PHY
[ 3.164662] rtk-usb2phy 98028280.dwc3_drd_usb2phy: do_rtk_usb2_phy_init Init RTK USB 2.0 PHY phy#0
[ 3.164710] rtk-usb2phy 98028280.dwc3_drd_usb2phy: do_rtk_usb2_phy_toggle ########## to toggle Page1 addr 0xe0 BIT(2)
[ 3.164757] rtk-usb-manager 98000000.rtk_usb_power_manager: rtk_usb_manager_schedule_work for 98013e00.rtk_dwc3_u3host
[ 3.164771] rtk-dwc3 98013e00.rtk_dwc3_u3host: dwc3_rtk_probe ok! (take 0 ms)
[ 3.165227] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.165236] ehci-pci: EHCI PCI platform driver
[ 3.165275] ehci-rtk: EHCI realtek driver init
[ 3.165364] rtk-ehci 98013000.ehci: Probe Realtek-SoC USB EHCI Host Controller
[ 3.165422] rtk-ehci 98013000.ehci: ehci_rtk_drv_probe Enable fixed_async_list_addr_bug
[ 3.165468] rtk-usb-manager 98000000.rtk_usb_power_manager: rtk_usb_manager_schedule_work for 98013000.ehci
[ 3.165482] rtk-ehci 98013000.ehci: ehci_rtk_drv_probe OK (take 0 ms)
[ 3.165642] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.165726] rtk-usb2phy 98028280.dwc3_drd_usb2phy: do_rtk_usb2_phy_toggle disconnect to set Page0 0xE7 = f1
[ 3.165733] rtk-usb2phy 98028280.dwc3_drd_usb2phy: rtk_usb2_phy_init Initialized RTK USB 2.0 PHY (take 0ms)
[ 3.165739] rtk-usb3phy 98013210.dwc3_drd_usb3phy: rtk_usb_phy_init Init RTK USB 3.0 PHY
[ 3.165746] rtk-usb3phy 98013210.dwc3_drd_usb3phy: do_rtk_usb_phy_init Init RTK USB 3.0 PHY phy#0
[ 3.165749] rtk-ohci 98013400.ohci: Probe Realtek-SoC USB OHCI Host Controller
[ 3.165849] rtk-usb-manager 98000000.rtk_usb_power_manager: rtk_usb_manager_schedule_work for 98013400.ohci
[ 3.165863] rtk-ohci 98013400.ohci: ohci_rtk_drv_probe OK (take 0 ms)
[ 3.166010] ohci-pci: OHCI PCI platform driver
[ 3.166530] usbcore: registered new interface driver usb-storage
[ 3.166571] usbcore: registered new interface driver ums-realtek
[ 3.166716] [RTK_RTC] 9801b600.rtc: rtk_base_year = 2016
[ 3.166887] [RTK_RTC] 9801b600.rtc: rtk_rtc rtcacr = 0x80
[ 3.166893] [RTK_RTC] 9801b600.rtc: rtk_rtc already enabled
[ 3.166901] [RTK_RTC] 9801b600.rtc: enable REG_SEC = 0x46
[ 3.166906] [RTK_RTC] 9801b600.rtc: enable REG_MIN = 0x13
[ 3.166911] [RTK_RTC] 9801b600.rtc: enable REG_HR = 0xb
[ 3.166917] [RTK_RTC] 9801b600.rtc: enable REG_DATA_LOW = 0x0
[ 3.166921] [RTK_RTC] 9801b600.rtc: enable REG_DATE_HIGH = 0x0
[ 3.167141] [RTK_RTC] 9801b600.rtc: rtc core: registered rtc as rtc0
[ 3.167147] [RTK_RTC] 9801b600.rtc: initialized
[ 3.167217] i2c /dev entries driver
[ 3.171599] rtk-usb3phy 98013210.dwc3_drd_usb3phy: do_rtk_usb3_phy_toggle ########## to toggle PHY addr 0x09 BIT(9)
[ 3.172909] rtk-usb3phy 98013210.dwc3_drd_usb3phy: do_rtk_usb3_phy_toggle ########## PHY addr 0x1f = 0x70081f10
[ 3.172916] rtk-usb3phy 98013210.dwc3_drd_usb3phy: rtk_usb_phy_init Initialized RTK USB 3.0 PHY (take 8ms)
[ 3.172958] dwc3 98020000.dwc3_drd: dwc3_gadget_init Enter
[ 3.173318] dwc3 98020000.dwc3_drd: dwc3_gadget_init Exit
[ 3.173946] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: ENTER dwc3_rtk_type_c_probe
[ 3.173966] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: No mapping memory for type_c_reg_base!
[ 3.173972] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: Let type_c_reg_base = ffffff80093f434c
[ 3.174053] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: dwc3_rtk_type_c_probe get rd_ctrl-gpio (id=135) OK
[ 3.174062] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: Set device mode boot_check_time -1 ms ==> (Disable to check)
[ 3.174068] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: Set filter_config_channel_signal is False
[ 3.174078] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: Chip 1296 revision is b01 (support revision a01) to load A01 parameter
[ 3.174138] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: DWC3_DRD is DRD mode
[ 3.174186] rtk-usb-manager 98000000.rtk_usb_power_manager: rtk_usb_manager_schedule_work for 98013200.rtk_dwc3_drd_type_c
[ 3.174205] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: create_debug_files
[ 3.174240] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: Exit dwc3_rtk_type_c_probe OK (take 4 ms)
[ 3.174285] rtk-dwc3 98013200.rtk_dwc3_drd: dwc3_rtk_probe_work End ... ok! (take 12 ms)
[ 3.174293] rtk-dwc3 98013c00.rtk_dwc3_u2host: dwc3_rtk_probe_work Start ...
[ 3.174545] dwc3 98029000.dwc3_u2host: rtk dwc3 fixed dwc3 globals register start address 0xffffff8009618100
[ 3.174654] rtk-usb2phy 98031280.dwc3_u2host_usb2phy: rtk_usb2_phy_init Init RTK USB 2.0 PHY
[ 3.174661] rtk-usb2phy 98031280.dwc3_u2host_usb2phy: do_rtk_usb2_phy_init Init RTK USB 2.0 PHY phy#0
[ 3.174707] rtk-usb2phy 98031280.dwc3_u2host_usb2phy: do_rtk_usb2_phy_toggle ########## to toggle Page1 addr 0xe0 BIT(2)
[ 3.175722] rtk-usb2phy 98031280.dwc3_u2host_usb2phy: do_rtk_usb2_phy_toggle disconnect to set Page0 0xE7 = f1
[ 3.175728] rtk-usb2phy 98031280.dwc3_u2host_usb2phy: rtk_usb2_phy_init Initialized RTK USB 2.0 PHY (take 0ms)
[ 3.175764] dwc3 98029000.dwc3_u2host: dwc3_host_init
[ 3.175942] xhci-hcd xhci-hcd.6.auto: xHCI Host Controller
[ 3.175961] xhci-hcd xhci-hcd.6.auto: new USB bus registered, assigned bus number 1
[ 3.176208] xhci-hcd xhci-hcd.6.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x02010010
[ 3.176253] xhci-hcd xhci-hcd.6.auto: irq 9, io mem 0x98029000
[ 3.176935] hub 1-0:1.0: USB hub found
[ 3.176966] hub 1-0:1.0: 1 port detected
[ 3.177235] xhci-hcd xhci-hcd.6.auto: xHCI Host Controller
[ 3.177247] xhci-hcd xhci-hcd.6.auto: new USB bus registered, assigned bus number 2
[ 3.177316] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.177894] hub 2-0:1.0: USB hub found
[ 3.177923] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 3.178216] rtk-usb-manager 98000000.rtk_usb_power_manager: rtk_usb_init_port_power_on for 98013c00.rtk_dwc3_u2host
[ 3.178227] rtk-usb-manager 98000000.rtk_usb_power_manager: __usb_port_power_on_off port1 power=on enable=0x1 enable_mask=0x1
[ 3.178235] rtk-usb-manager 98000000.rtk_usb_power_manager: gpio_num=132 enable_port=0x2 enable_port_mask=0x6 ==> No turn on
[ 3.178242] rtk-dwc3 98013c00.rtk_dwc3_u2host: dwc3_rtk_probe_work End ... ok! (take 4 ms)
[ 3.178250] rtk-dwc3 98013e00.rtk_dwc3_u3host: dwc3_rtk_probe_work Start ...
[ 3.178508] dwc3 981f0000.dwc3_u3host: rtk dwc3 fixed dwc3 globals register start address 0xffffff8009648100
[ 3.178653] rtk-usb2phy 981f8280.dwc3_u3host_usb2phy: rtk_usb2_phy_init Init RTK USB 2.0 PHY
[ 3.178660] rtk-usb2phy 981f8280.dwc3_u3host_usb2phy: do_rtk_usb2_phy_init Init RTK USB 2.0 PHY phy#0
[ 3.178713] rtk-usb2phy 981f8280.dwc3_u3host_usb2phy: do_rtk_usb2_phy_toggle ########## to toggle Page1 addr 0xe0 BIT(2)
[ 3.179730] rtk-usb2phy 981f8280.dwc3_u3host_usb2phy: do_rtk_usb2_phy_toggle disconnect to set Page0 0xE7 = f1
[ 3.179736] rtk-usb2phy 981f8280.dwc3_u3host_usb2phy: rtk_usb2_phy_init Initialized RTK USB 2.0 PHY (take 0ms)
[ 3.179743] rtk-usb3phy 98013e10.dwc3_u3host_usb3phy: rtk_usb_phy_init Init RTK USB 3.0 PHY
[ 3.179749] rtk-usb3phy 98013e10.dwc3_u3host_usb3phy: do_rtk_usb_phy_init Init RTK USB 3.0 PHY phy#0
[ 3.185605] rtk-usb3phy 98013e10.dwc3_u3host_usb3phy: do_rtk_usb3_phy_toggle ########## to toggle PHY addr 0x09 BIT(9)
[ 3.186915] rtk-usb3phy 98013e10.dwc3_u3host_usb3phy: do_rtk_usb3_phy_toggle ########## PHY addr 0x1f = 0x90001f10
[ 3.186922] rtk-usb3phy 98013e10.dwc3_u3host_usb3phy: rtk_usb_phy_init Initialized RTK USB 3.0 PHY (take 8ms)
[ 3.186958] dwc3 981f0000.dwc3_u3host: dwc3_host_init
[ 3.187119] xhci-hcd xhci-hcd.7.auto: xHCI Host Controller
[ 3.187135] xhci-hcd xhci-hcd.7.auto: new USB bus registered, assigned bus number 3
[ 3.187393] xhci-hcd xhci-hcd.7.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x02010010
[ 3.187417] xhci-hcd xhci-hcd.7.auto: irq 9, io mem 0x981f0000
[ 3.188019] hub 3-0:1.0: USB hub found
[ 3.188050] hub 3-0:1.0: 1 port detected
[ 3.188305] xhci-hcd xhci-hcd.7.auto: xHCI Host Controller
[ 3.188317] xhci-hcd xhci-hcd.7.auto: new USB bus registered, assigned bus number 4
[ 3.188387] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.188921] hub 4-0:1.0: USB hub found
[ 3.188949] hub 4-0:1.0: 1 port detected
[ 3.189311] rtk-usb-manager 98000000.rtk_usb_power_manager: rtk_usb_init_port_power_on for 98013e00.rtk_dwc3_u3host
[ 3.189321] rtk-usb-manager 98000000.rtk_usb_power_manager: __usb_port_power_on_off port3 power=on enable=0x1 enable_mask=0x1
[ 3.189363] rtk-usb-manager 98000000.rtk_usb_power_manager: __gpio_on_off to set power on by gpio (id=133) OK
[ 3.189375] rtk-dwc3 98013e00.rtk_dwc3_u3host: dwc3_rtk_probe_work End ... ok! (take 8 ms)
[ 3.189382] rtk-ehci 98013000.ehci: ehci_rtk_probe_work Start ...
[ 3.189389] rtk-usb-phy-rle0599 98013824.usb_phy_rle0599: Init RTK USB phy-rle0599
[ 3.189473] rtk-usb-phy-rle0599 98013824.usb_phy_rle0599: rtk_rle0599_phy_toggle ########## to toggle Page1 addr 0xe0 BIT(2)
[ 3.190485] rtk-usb-phy-rle0599 98013824.usb_phy_rle0599: drivers/usb/phy/phy-rtk-rle0599.c Initialized RTK USB PHY rle0599
[ 3.190512] rtk-ehci 98013000.ehci: EHCI Host Controller
[ 3.190531] rtk-ehci 98013000.ehci: new USB bus registered, assigned bus number 5
[ 3.190678] rtk-ehci 98013000.ehci: irq 9, io mem 0x98013000
[ 3.193714] rtk-thermal-sensor 9801d150.thermal-sensor: initialized
[ 3.205632] rtk-ehci 98013000.ehci: USB 2.0 started, EHCI 1.00
[ 3.206246] hub 5-0:1.0: USB hub found
[ 3.206274] hub 5-0:1.0: 1 port detected
[ 3.206576] rtk-usb-manager 98000000.rtk_usb_power_manager: rtk_usb_init_port_power_on for 98013000.ehci
[ 3.206585] rtk-usb-manager 98000000.rtk_usb_power_manager: __usb_port_power_on_off port2 power=on enable=0x1 enable_mask=0x3
[ 3.206592] rtk-ehci 98013000.ehci: ehci_rtk_probe_work End ... ok! (take 20 ms)
[ 3.206599] rtk-ohci 98013400.ohci: ohci_rtk_probe_work Start ...
[ 3.206607] rtk-ohci 98013400.ohci: Rtk Dmp OHCI
[ 3.206624] rtk-ohci 98013400.ohci: new USB bus registered, assigned bus number 6
[ 3.206638] rtk-ohci 98013400.ohci: _ohci_readl [USB Workaround] fixed force to enable ohci clock
[ 3.207767] rtk-ohci 98013400.ohci: irq 9, io mem 0x98013400
[ 3.219848] rtk-thermal-sensor 980124b4.thermal-sensor: initialized
[ 3.221880] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com
[ 3.222509] EMMC : emmc of_node found
[ 3.222581] [rtkemmc_probe] get speed-step : 2
[ 3.222586] [rtkemmc_probe] no driving nf_s1 warning !!
[ 3.222590] [rtkemmc_probe] get driving s2 : 0x1
[ 3.222592] [rtkemmc_probe] get driving s2 : 0xbb
[ 3.222595] [rtkemmc_probe] get driving s2 : 0xbb
[ 3.222597] [rtkemmc_probe] get driving s2 : 0xbb
[ 3.222599] [rtkemmc_probe] get driving s2 : 0x33
[ 3.222603] [rtkemmc_probe] no driving nf_s3 warning !!
[ 3.222606] [rtkemmc_probe] get tx tuning switch : 0
[ 3.222609] [rtkemmc_probe] get rx tuning switch : 0
[ 3.222612] [rtkemmc_probe] no dqs_tuning switch node !!
[ 3.222615] [rtkemmc_probe] no tx & rx reference phase switch node !!
[ 3.222619] [rtkemmc_probe] No emmc tuning offset node, using MBR format !!
[ 3.222711] rtkemmc_set_pin_mux: EMMC_PFUNC_NF1 = 0x33333333
[ 3.222741] EMMC: set to 0x00000000, EMMC_CTYPE=00000000
[ 3.222749] EMMC: set_wrapper_div to 0x00002100
[ 3.222752] EMMC, set_ip_div = cur_div(0x00000080), ignored.
[ 3.223397] EMMC: set_freq to 0x46, EMMC_CKGEN_CTL=0x00002100, PLL_EMMC1=00000003, PLL_EMMC2=04517893, PLL_EMMC3=00464388, PLL_EMMC4=00000007
[ 3.223922] EMMC: set_freq to 0x46, EMMC_CKGEN_CTL=0x00002100, PLL_EMMC1=00000003, PLL_EMMC2=04517893, PLL_EMMC3=00464388, PLL_EMMC4=00000007
[ 3.223925] EMMC, set_ip_div = cur_div(0x00000080), ignored.
[ 3.242055] EMMC: set_freq to 0x46, EMMC_CKGEN_CTL=0x00002100, PLL_EMMC1=00000003, PLL_EMMC2=04517893, PLL_EMMC3=00464388, PLL_EMMC4=00000007
[ 3.242059] EMMC, set_ip_div = cur_div(0x00000080), ignored.
[ 3.261635] mmc0: EMMC driver initialized
[ 3.262077] EMMC: set_freq to 0x46, EMMC_CKGEN_CTL=0x00002100, PLL_EMMC1=00000003, PLL_EMMC2=04517893, PLL_EMMC3=00464388, PLL_EMMC4=00000007
[ 3.262081] EMMC, set_ip_div = cur_div(0x00000080), ignored.
[ 3.265399] EMMC: set_freq to 0x46, EMMC_CKGEN_CTL=0x00002100, PLL_EMMC1=00000003, PLL_EMMC2=04517893, PLL_EMMC3=00464388, PLL_EMMC4=00000007
[ 3.265403] EMMC, set_ip_div = cur_div(0x00000080), ignored.
[ 3.266837] EMMC: set_freq to 0x46, EMMC_CKGEN_CTL=0x00002100, PLL_EMMC1=00000003, PLL_EMMC2=04517893, PLL_EMMC3=00464388, PLL_EMMC4=00000007
[ 3.266840] EMMC, set_ip_div = cur_div(0x00000080), ignored.
[ 3.270263] hub 6-0:1.0: USB hub found
[ 3.270297] hub 6-0:1.0: 1 port detected
[ 3.270500] EMMC: set_freq to 0x46, EMMC_CKGEN_CTL=0x00002100, PLL_EMMC1=00000003, PLL_EMMC2=04517893, PLL_EMMC3=00464388, PLL_EMMC4=00000007
[ 3.270504] EMMC, set_ip_div = cur_div(0x00000080), ignored.
[ 3.270591] rtk-usb-manager 98000000.rtk_usb_power_manager: rtk_usb_init_port_power_on for 98013400.ohci
[ 3.270601] rtk-usb-manager 98000000.rtk_usb_power_manager: __usb_port_power_on_off port2 power=on enable=0x3 enable_mask=0x3
[ 3.270639] rtk-usb-manager 98000000.rtk_usb_power_manager: __gpio_on_off to set power on by gpio (id=132) OK
[ 3.270650] rtk-ohci 98013400.ohci: ohci_rtk_probe_work End ... ok! (take 64 ms)
[ 3.270659] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: dwc3_rtk_type_c_probe_work Start ...
[ 3.270667] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: dwc3_rtk_type_c_init set debounce = 0x7f (check--> 0xff)
[ 3.270689] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: rtk_type_c_init
[ 3.270736] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: switch_dwc3_mode dr_mode=0
[ 3.270742] dwc3 98020000.dwc3_drd: dwc3_drd_to_stop_all START....
[ 3.270747] dwc3 98020000.dwc3_drd: dwc3_gadget_exit Enter
[ 3.270895] dwc3 98020000.dwc3_drd: dwc3_gadget_exit Exit
[ 3.270901] dwc3 98020000.dwc3_drd: dwc3_drd_to_stop_all END....
[ 3.270907] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: DWC3_DRD run in USB_DR_MODE_PERIPHERAL at DRD mode
[ 3.270913] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: First time device mode check is Diable
[ 3.270933] EMMC: set_freq to 0x46, EMMC_CKGEN_CTL=0x00002100, PLL_EMMC1=00000003, PLL_EMMC2=04517893, PLL_EMMC3=00464388, PLL_EMMC4=00000007
[ 3.270937] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: dwc3_rtk_type_c_probe_work End ... ok! (take 0 ms)
[ 3.270939] EMMC, set_ip_div = cur_div(0x00000080), ignored.
[ 3.273576] EMMC: set_freq to 0x46, EMMC_CKGEN_CTL=0x00002100, PLL_EMMC1=00000003, PLL_EMMC2=04517893, PLL_EMMC3=00464388, PLL_EMMC4=00000007
[ 3.273580] EMMC, set_ip_div = cur_div(0x00000080), ignored.
[ 3.279282] EMMC: set_freq to 0x46, EMMC_CKGEN_CTL=0x00002100, PLL_EMMC1=00000003, PLL_EMMC2=04517893, PLL_EMMC3=00464388, PLL_EMMC4=00000007
[ 3.279285] EMMC, set_ip_div = cur_div(0x00000080), ignored.
[ 3.279977] rtkemmc_set_rspparam : cmd7 arg : 0x00010000
[ 3.279980] rtkemmc_set_rspparam : cmd7 with rsp
[ 3.289672] xhci-hcd xhci-hcd.7.auto: RTK_phy_toggle to call RTK_dwc3_usb2_phy_toggle (wValue=10 port=0 status=202a0)
[ 3.289683] rtk-usb2phy 981f8280.dwc3_u3host_usb2phy: do_rtk_usb2_phy_toggle ########## to toggle Page1 addr 0xe0 BIT(2)
[ 3.290699] rtk-usb2phy 981f8280.dwc3_u3host_usb2phy: do_rtk_usb2_phy_toggle disconnect to set Page0 0xE7 = f1
[ 3.295855] card->mmc_avail_type = 0x00000013
[ 3.297103] EMMC: set_freq to 0x46, EMMC_CKGEN_CTL=0x00002100, PLL_EMMC1=00000003, PLL_EMMC2=04517893, PLL_EMMC3=00464388, PLL_EMMC4=00000007
[ 3.297107] EMMC, set_ip_div = cur_div(0x00000080), ignored.
[ 3.297108] set bus width 8
[ 3.297114] EMMC: set to 0x00010000, EMMC_CTYPE=00010000
[ 3.300494] EMMC: set_freq to 0xa6, EMMC_CKGEN_CTL=0x00002100, PLL_EMMC1=00000003, PLL_EMMC2=04517893, PLL_EMMC3=00a64388, PLL_EMMC4=00000007
[ 3.300505] EMMC: set div to 0x00, EMMC_CLKDIV=00000000
[ 3.300507] set bus width 8
[ 3.300512] EMMC: set to 0x00010000, EMMC_CTYPE=00010000
[ 3.300943] EMMC: set_freq to 0xa6, EMMC_CKGEN_CTL=0x00002100, PLL_EMMC1=00000003, PLL_EMMC2=04517893, PLL_EMMC3=00a64388, PLL_EMMC4=00000007
[ 3.300946] EMMC, set_ip_div = cur_div(0x00000000), ignored.
[ 3.300948] set bus width 8
[ 3.300953] EMMC: set to 0x00010000, EMMC_CTYPE=00010000
[ 3.300958] emmc card manid = 0x00000015
[ 3.300962] EMMC: set_wrapper_div to 0x00002100
[ 3.301391] EMMC: set_freq to 0xa6, EMMC_CKGEN_CTL=0x00002100, PLL_EMMC1=00000003, PLL_EMMC2=04517893, PLL_EMMC3=00a64388, PLL_EMMC4=00000007
[ 3.301394] EMMC, set_ip_div = cur_div(0x00000000), ignored.
[ 3.301609] Inherit bootcode tuning phase: TX=0x11, RX=0x17
[ 3.311614] HS200: final phase=0x178b
[ 3.312760] mmc0: new HS200 MMC card at address 0001
[ 3.313235] mmcblk0: mmc0:0001 8GTF4R 7.28 GiB
[ 3.313477] mmcblk0boot0: mmc0:0001 8GTF4R partition 1 4.00 MiB
[ 3.317728] mmcblk0boot1: mmc0:0001 8GTF4R partition 2 4.00 MiB
[ 3.321950] mmcblk0rpmb: mmc0:0001 8GTF4R partition 3 512 KiB
[ 3.322652] mmcblk0: p1 p2
[ 3.325628] mmc0: retry_left=46, block_dev=[16 -> 22], time=61ms
[ 3.325765] sdhci: Secure Digital Host Controller Interface driver
[ 3.325767] sdhci: Copyright(c) Pierre Ossman
[ 3.325769] sdhci-pltfm: SDHCI platform and OF driver helper
[ 3.325926] rtk-sdio: build at : #0 SMP PREEMPT Mon Apr 8 13:55:47 2024
[ 3.413632] [SDIO] SDHCI_SPEC_300: rtk_sdhci_set_clock end real_div=1f4, div=fa, c3c=0, PLL=ae4388, CLK=fa07
[ 3.433631] mmc1: SDHCI controller on 98010c00.sdio [98010c00.sdio] using ADMA
[ 3.433920] rtk_sdmmc_probe: clk_get() returns -2
[ 3.433939] rtk-sdmmc: build at : #0 SMP PREEMPT Mon Apr 8 13:55:47 2024
[ 3.433941] rtk-sdmmc: CONFIG_MMC_BLOCK_BOUNCE enable
[ 3.437881] rtk-sdio 98010c00.sdio: card claims to support voltages below defined range
[ 3.440557] SDIO 3.0 A01 version
[ 3.440559] SDIO SDR104 mode
[ 3.451142] [SDIO] SDHCI_SPEC_300: rtk_sdhci_set_clock end real_div=1, div=0, c3c=b0000, PLL=ae4388, CLK=7
[ 3.451149] rtk_sdhci_execute_tuning : Execute Clock Phase Tuning
[ 3.462779] rtk_sdhci_tuning_tx TX phase_map = 0xfe3fffff
[ 3.462783] rtk_sdhci_tuning_tx final phase = 0x00000007
[ 3.474971] rtk_sdhci_tuning_rx RX phase_map = 0xfffc03ff
[ 3.474976] rtk_sdhci_tuning_rx final phase = 0x0000001e
[ 3.475080] After tuning, current SDIO PLL = ae
[ 3.475156] random: fast init done
[ 3.476152] mmc1: new ultra high speed SDR104 SDIO card at address 0001
[ 3.489638] rtk_sdmmc_get_cd: SD card does not exist, regCARD_EXIST = 20
[ 3.502617] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 3.503844] [sound/arm/snd-realtek.c snd_card_create_PCM_instance 4172]
[ 3.503952] [sound/arm/snd-realtek.c snd_card_create_PCM_instance 4172]
[ 3.503992] [sound/arm/snd-realtek.c snd_card_create_PCM_instance 4172]
[ 3.504029] [sound/arm/snd-realtek.c snd_card_create_PCM_instance 4172]
[ 3.504070] [sound/arm/snd-realtek.c snd_card_create_PCM_instance 4172]
[ 3.504107] [sound/arm/snd-realtek.c snd_card_create_PCM_instance 4172]
[ 3.528428] NET: Registered protocol family 10
[ 3.550300] NET: Registered protocol family 17
[ 3.550366] 8021q: 802.1Q VLAN Support v1.8
[ 3.550392] Key type dns_resolver registered
[ 3.557566] Registered cp15_barrier emulation handler
[ 3.557576] Registered setend emulation handler
[ 3.558118] registered taskstats version 1
[ 3.560848] [RTK_SCPU_WRAPPER] scpu wrappee irq 25, scpu_wrap_addr 0xffffff80096da000
[ 3.560894] [RTK_SCPU_WRAPPER] initialized
[ 3.560897] [RTK_SCPU_WRAPPER] memory monitor 0x98013b00 - 0x98013c00
[ 3.561498] rtk-uctrl rtk-uctrl.0: initialized
[ 3.561730] rtk-ccsc rtk-ccsc: initialized
[ 3.564279] [RTK_RTC] 9801b600.rtc: setting system clock to 2016-01-01 11:19:35 UTC (1451647175)
[ 3.565251] audio-notifier audio-out-devices: rtk_audio_notifier_probe
[ 3.565275] audio-notifier audio-out-devices: i2s: mode=master, channel=2
[ 3.565394] clk_mmio_gate_disable_unused: clk_en_ur2
[ 3.565406] clk_mmio_gate_disable_unused: clk_en_misc_i2c_1
[ 3.565427] clk_mmio_gate_disable_unused: clk_en_nf
[ 3.565457] pll_ddsb: clk_pll_disable_unused
[ 3.565477] pctrl_gpu: rtk_sram_power_off_unused
[ 3.565491] ALSA device list:
[ 3.565494] #0: snd_alsa_rtk
[ 5.382112] ttyS0 - failed to request DMA
[ 5.388287] VFS: Mounted root (squashfs filesystem) readonly on device 179:1.
[ 5.400168] devtmpfs: mounted
[ 5.404590] Freeing unused kernel memory: 3392K
[ 5.866042] init: Console is alive
[ 6.545713] ahci_rtk 9803f000.sata: masking port_map 0x3 -> 0x3
[ 6.551855] ahci_rtk 9803f000.sata: AHCI 0001.0301 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 6.560966] ahci_rtk 9803f000.sata: flags: ncq sntf pm led clo only pmp fbs pio slum part ccc sadm sds apst
[ 6.577210] scsi host0: ahci_rtk
[ 6.584948] scsi host1: ahci_rtk
[ 6.588469] ata1: SATA max UDMA/133 mmio [mem 0x9803f000-0x9803ffff] port 0x100 irq 10
[ 6.596596] ata2: SATA max UDMA/133 mmio [mem 0x9803f000-0x9803ffff] port 0x180 irq 10
[ 6.721012] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.813629] phy-rtk-sata 9803ff00.sata_phy: power on phy1
[ 6.817691] raid6: int64x1 gen() 267 MB/s
[ 6.823596] phy-rtk-sata 9803ff00.sata_phy: power on phy0
[ 6.885638] raid6: int64x1 xor() 240 MB/s
[ 6.930463] ata1: SATA link down (SStatus 0 SControl 300)
[ 6.957721] raid6: int64x2 gen() 432 MB/s
[ 7.029671] raid6: int64x2 xor() 366 MB/s
[ 7.101682] raid6: int64x4 gen() 606 MB/s
[ 7.173638] raid6: int64x4 xor() 437 MB/s
[ 7.245672] raid6: int64x8 gen() 491 MB/s
[ 7.317682] raid6: int64x8 xor() 401 MB/s
[ 7.389662] raid6: neonx1 gen() 477 MB/s
[ 7.461671] raid6: neonx1 xor() 472 MB/s
[ 7.533620] raid6: neonx2 gen() 728 MB/s
[ 7.605612] raid6: neonx2 xor() 639 MB/s
[ 7.677610] raid6: neonx4 gen() 989 MB/s
[ 7.749624] raid6: neonx4 xor() 754 MB/s
[ 7.821634] raid6: neonx8 gen() 992 MB/s
[ 7.893633] raid6: neonx8 xor() 755 MB/s
[ 7.898020] raid6: using algorithm neonx8 gen() 992 MB/s
[ 7.903470] raid6: .... xor() 755 MB/s, rmw enabled
[ 7.908477] raid6: using intx1 recovery algorithm
[ 7.913823] xor: measuring software checksum speed
[ 7.957610] 8regs : 1437.000 MB/sec
[ 8.001622] 8regs_prefetch: 1288.000 MB/sec
[ 8.045603] 32regs : 1868.000 MB/sec
[ 8.089621] 32regs_prefetch: 1626.000 MB/sec
[ 8.094370] xor: using function: 32regs (1868.000 MB/sec)
[ 8.301701] Btrfs loaded, crc32c=crc32c-arm64-hw
[ 8.312206] exFAT: Version 1.2.9
[ 8.553170] SGI XFS with ACLs, security attributes, no debug enabled
[ 8.563251] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 8.580787] init: - preinit -
[ 9.109411] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.131831] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.144380] Starting lvm2 during preinit
[ 9.720244] random: lvm: uninitialized urandom read (4 bytes read)
[ 10.326919] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 10.372817] urandom-seed: Seeding with /etc/urandom.seed
[ 10.433393] procd: - early -
[ 11.075859] procd: - ubus -
[ 11.132411] urandom_read: 1 callbacks suppressed
[ 11.132416] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.143892] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.150437] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.157419] procd: - init -
[ 11.311743] write procfs ethernet wol_enable = 1
[ 11.392530] kmodloader: loading kernel modules from /etc/modules.d/*
[ 11.444495] md: linear personality registered for level -1
[ 11.451056] md: raid0 personality registered for level 0
[ 11.458773] md: raid1 personality registered for level 1
[ 11.467002] md: raid10 personality registered for level 10
[ 11.473154] async_tx: api initialized (async)
[ 11.486629] md: raid6 personality registered for level 6
[ 11.492098] md: raid5 personality registered for level 5
[ 11.497585] md: raid4 personality registered for level 4
[ 11.504009] md: multipath personality registered for level -4
[ 11.528255] tun: Universal TUN/TAP device driver, 1.6
[ 11.533462] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 11.543446] gre: GRE over IPv4 demultiplexor driver
[ 11.549528] ip_gre: GRE over IPv4 tunneling driver
[ 11.588751] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 11.602165] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 11.613562] cryptodev: driver 1.9 loaded.
[ 11.618610] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[ 11.626832] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[ 11.745805] fuse init (API version 7.26)
[ 11.985642] ata2: link is slow to respond, please be patient (ready=0)
[ 12.260177] RTW: module init start
[ 12.263697] RTW: rtl8812au v5.2.20.2_28373.20180619_v0.17_20181026
[ 12.270076] RTW: build time: Apr 8 2024 13:55:47
[ 12.275041] usbcore: registered new interface driver rtl8812au
[ 12.281034] RTW: module init ret=0
[ 12.844969] RTW: module init start
[ 12.848485] RTW: rtl8821cu v5.4.1_28754.20180921_COEX20180712-3232_v0.14_20190516
[ 12.856161] RTW: build time: Apr 8 2024 13:55:47
[ 12.860990] RTW: rtl8821cu BT-Coex version = COEX20180712-3232
[ 12.867110] usbcore: registered new interface driver rtl8821cu
[ 12.873101] RTW: module init ret=0
[ 13.418832] RTW: module init start
[ 13.422345] RTW: rtl88x2cs v5.12.1.1-0-gf673ce3.20210125_COEX20200922-1e1e
[ 13.429398] RTW: build time: Apr 8 2024 13:55:47
[ 13.434229] RTW: rtl88x2cs BT-Coex version = COEX20200922-1e1e
[ 13.440581] RTW: == SDIO Card Info ==
[ 13.444354] RTW: card: ffffffc07a87c800
[ 13.448473] RTW: clock: 200000000 Hz
[ 13.452325] RTW: timing spec: sd uhs SDR104
[ 13.456827] RTW: sd3_bus_mode: TRUE
[ 13.460588] RTW: func num: 1
[ 13.463732] RTW: func1: ffffffc07a848400 (*)
[ 13.468294] RTW: ================
[ 13.471871] RTW: [HALMAC]55772M
[ 13.471871] HALMAC_MAJOR_VER = 1
[ 13.471871] HALMAC_PROTOTYPE_VER = 6
[ 13.471871] HALMAC_MINOR_VER = 6
[ 13.471871] HALMAC_PATCH_VER = 22
[ 13.533556] RTW: HW EFUSE
[ 13.536287] RTW: 0x000: 29 81 00 8F FF 20 28 00 9A 04 ED 75 10 0F F1 EB
[ 13.543774] RTW: 0x010: 4D 4D 4F 4F 4F 4F 40 40 42 42 42 04 00 00 FF FF
[ 13.551258] RTW: 0x020: FF FF 3F 3C 40 40 39 39 39 3A 3C 36 37 38 39 40
[ 13.558741] RTW: 0x030: 04 00 FF FF 00 FF 00 00 FF FF 53 53 56 5A 5A 5A
[ 13.566221] RTW: 0x040: 45 45 48 4C 4C 04 00 00 FF FF FF FF 42 44 41 43
[ 13.573731] RTW: 0x050: 3B 3A 3D 41 41 42 3E 40 40 3F 04 00 FF FF 00 FF
[ 13.581205] RTW: 0x060: 00 00 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.588687] RTW: 0x070: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.596172] RTW: 0x080: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.603656] RTW: 0x090: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.611134] RTW: 0x0A0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.618616] RTW: 0x0B0: FF FF FF FF FF FF FF FF 7F 45 FF 00 FF FF FF FF
[ 13.626120] RTW: 0x0C0: FF 21 00 10 00 00 FF FF 00 33 04 FF FF FF FF FF
[ 13.633606] RTW: 0x0D0: 1C 20 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.641078] RTW: 0x0E0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.648563] RTW: 0x0F0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.656043] RTW: 0x100: F0 94 65 D3 58 C5 FF FF CD F0 FF FF FF FF FF FF
[ 13.663519] RTW: 0x110: 45 45 FC A0 D8 D8 FD FF 35 8C FF FF FF FF FF FF
[ 13.670998] RTW: 0x120: FE DF 01 23 34 FF FF FF FF FF 4C 02 22 C8 FF FF
[ 13.678477] RTW: 0x130: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.685988] RTW: 0x140: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.693453] RTW: 0x150: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.700937] RTW: 0x160: FF FF FF FF FF FF FF FF FF FF F0 B0 40 6F B9 F9
[ 13.708417] RTW: 0x170: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.715895] RTW: 0x180: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.723379] RTW: 0x190: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.730857] RTW: 0x1A0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.738368] RTW: 0x1B0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.745877] RTW: 0x1C0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.753353] RTW: 0x1D0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.760848] RTW: 0x1E0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.768338] RTW: 0x1F0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.775826] RTW: 0x200: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.783308] RTW: 0x210: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.790799] RTW: 0x220: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.798324] RTW: 0x230: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.805808] RTW: 0x240: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.813280] RTW: 0x250: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.820766] RTW: 0x260: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.828245] RTW: 0x270: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.835725] RTW: 0x280: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.843212] RTW: 0x290: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.850720] RTW: 0x2A0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.858203] RTW: 0x2B0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.865688] RTW: 0x2C0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.873162] RTW: 0x2D0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.880644] RTW: 0x2E0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.888127] RTW: 0x2F0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.895619] RTW: hal_com_config_channel_plan chplan:0x7F
[ 13.924730] RTW: WARN Invalid rate 0x0 in MRateToHwRate
[ 13.930110] RTW: WARN Invalid rate 0x0 in MRateToHwRate
[ 13.935481] RTW: WARN Invalid rate 0x0 in MRateToHwRate
[ 13.955667] RTW: [RF_PATH] ver_id.RF_TYPE:RF_2T2R
[ 13.960508] RTW: [RF_PATH] HALSPEC's rf_reg_trx_path_bmp:0x33, rf_reg_path_avail_num:2, max_tx_cnt:2
[ 13.969901] RTW: [RF_PATH] PG's trx_path_bmp:0x33, max_tx_cnt:0
[ 13.975980] RTW: [RF_PATH] Registry's trx_path_bmp:0x00, tx_path_lmt:0, rx_path_lmt:0
[ 13.984013] RTW: [RF_PATH] HALDATA's trx_path_bmp:0x33, max_tx_cnt:2
[ 13.990533] RTW: [RF_PATH] HALDATA's rf_type:RF_2T2R, NumTotalRFPath:2
[ 13.997232] RTW: [TRX_Nss] HALSPEC - tx_nss:2, rx_nss:2
[ 14.002596] RTW: [TRX_Nss] Registry - tx_nss:0, rx_nss:0
[ 14.008048] RTW: [TRX_Nss] HALDATA - tx_nss:2, rx_nss:2
[ 14.013414] RTW: txpath=0x3, rxpath=0x3
[ 14.017356] RTW: txpath_1ss:0x1, num:1
[ 14.021209] RTW: txpath_2ss:0x3, num:2
[ 14.025724] RTW: rtw_regsty_chk_target_tx_power_valid return _FALSE for band:0, path:0, rs:0, t:-1
[ 14.039232] RTW: rtw_ndev_init(wlan0) if1 mac_addr=f0:b0:40:6f:b9:f9
[ 14.046895] RTW: rtw_ndev_init(wlan1) if2 mac_addr=f2:b0:40:6f:b9:f9
[ 14.054591] RTW: module init ret=0
[ 14.061231] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 14.076387] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 14.247187] xt_time: kernel timezone is -0000
[ 14.256994] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 16.212267] r8169 98016000.gmac eth0: rtl_csiar_cond == 0 (loop: 100, delay: 10).
[ 16.221286] r8169 98016000.gmac eth0: rtl_csiar_cond == 1 (loop: 100, delay: 10).
[ 16.230268] r8169 98016000.gmac eth0: link down
[ 16.235091] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 16.239939] r8169 98016000.gmac eth0: link down
[ 16.625659] ata2: COMRESET failed (errno=-16)
[ 18.945108] r8169 98016000.gmac eth0: link up
[ 18.949653] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 18.970881] r8169 98016000.gmac eth0: rtl_csiar_cond == 0 (loop: 100, delay: 10).
[ 18.979908] r8169 98016000.gmac eth0: rtl_csiar_cond == 1 (loop: 100, delay: 10).
[ 18.988904] r8169 98016000.gmac eth0: link up
[ 21.993664] ata2: link is slow to respond, please be patient (ready=0)
[ 25.781642] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 25.788699] ata2.00: ATA-10: ST6000NM0024-1HT17Z, MA29, max UDMA/133
[ 25.795586] ata2.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 25.803409] ata2.00: configured for UDMA/133
[ 25.808261] scsi 1:0:0:0: Direct-Access ATA ST6000NM0024-1HT MA29 PQ: 0 ANSI: 5
[ 25.854226] sd 1:0:0:0: [sda] 11721045168 512-byte logical blocks: (6.00 TB/5.46 TiB)
[ 25.862279] sd 1:0:0:0: [sda] 4096-byte physical blocks
[ 25.867829] sd 1:0:0:0: [sda] Write Protect is off
[ 25.872768] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 25.878046] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 25.940597] sda: sda1
[ 25.943941] sd 1:0:0:0: [sda] Attached SCSI disk
[ 37.105202] start ug_sys_log server
[ 37.612929] start ug_sys_log_monitor server
[ 39.215843] random: crng init done
[ 39.219342] random: 3 urandom warning(s) missed due to ratelimiting
[ 39.641032] ---ug_sys_log_monitor.sh sleep 10,before uptime 60 second
[ 39.977924] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 39.986052] NFSD: starting 90-second grace period (net ffffff800921e700)
[ 40.364953] md: md0 stopped.
[ 40.371995] md: bind<sda1>
[ 40.380476] md/raid1:md0: active with 1 out of 2 mirrors
[ 40.386138] created bitmap (44 pages) for device md0
[ 40.397887] md0: bitmap initialized from disk: read 3 pages, set 71 of 89423 bits
[ 40.426625] md0: detected capacity change from 0 to 6001039245312
[ 42.256566] aria2. start copy,Sat Feb 1 09:23:07 CST 2025
[ 42.262692] /data/.ugreen_nas/conf/
[ 42.280444] drwxrwxrwx 6 root root 4096 Feb 1 08:46 conf
[ 42.280444] drwxrwxrwx 3 root root 4096 Dec 9 2023 db
[ 42.280444] drwxrwxrwx 2 root root 4096 Jan 1 2021 log
[ 42.280444] drwxrwxrwx 2 root root 4096 Jan 1 2021 task_manager
[ 42.280444] drwxrwxrwx 5 root root 4096 Oct 24 2022 upgrade_dir
[ 42.317082] break
[ 42.324567] aria2. end copy,Sat Feb 1 09:23:07 CST 2025
[ 42.387359] begin syncthing config: Sat Feb 1 09:23:07 CST 2025
[ 42.617703] WARNING: Key exists; will not overwrite.
[ 42.622900] Device ID: 44YUUVD-2B572F6-VOWIMSA-JH226BS-F6FMTNB-V2FXYQM-35O7ZWB-L36SDQA
[ 42.662292] -rw-r--r-- 1 daemon daemon 794 May 29 2022 cert.pem
[ 42.662292] -rw------- 1 root root 8973 Feb 1 09:23 config.xml
[ 42.662292] -rw------- 1 daemon daemon 825 May 29 2022 csrftokens.txt
[ 42.662292] -rw-r--r-- 1 daemon daemon 802 Aug 11 17:32 https-cert.pem
[ 42.662292] -rw------- 1 daemon daemon 288 Aug 11 17:32 https-key.pem
[ 42.662292] drwxr-xr-x 2 daemon daemon 4096 Feb 1 08:53 index-v0.14.0.db
[ 42.662292] -rw------- 1 daemon daemon 288 May 29 2022 key.pem
[ 42.726902] userInfoExist: 1
[ 42.734377] <address>dynamic</address>
[ 42.734377] <address>dynamic</address>
[ 42.734377] <address>dynamic</address>
[ 42.734377] <address>dynamic</address>
[ 42.734377] <address>127.0.0.1:8394</address>
[ 42.734377] <user>ugreennasworkbench</user>
[ 42.734377] <password>$2a$10$Atv1ZeiWIJ2uSZdS9WUEt.6Jx6PWbQ.N7n6BL1BQ7jibRDszVKHOy</password>
[ 42.734377] <address>dynamic</address>
[ 42.777948] edit
[ 42.798900] end syncthing config: Sat Feb 1 09:23:08 CST 2025
[ 42.810027] <address>dynamic</address>
[ 42.810027] <address>dynamic</address>
[ 42.810027] <address>dynamic</address>
[ 42.810027] <address>dynamic</address>
[ 42.810027] <address>127.0.0.1:8394</address>
[ 42.810027] <user>ugreennasworkbench</user>
[ 42.810027] <password>$2a$10$Atv1ZeiWIJ2uSZdS9WUEt.6Jx6PWbQ.N7n6BL1BQ7jibRDszVKHOy</password>
[ 42.810027] <address>dynamic</address>
[ 43.988477] EXT4-fs (md0): barriers disabled
[ 46.866858] EXT4-fs (md0): recovery complete
[ 46.914246] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: nobarrier,usrquota,grpquota,prjquota
[ 48.540321] Adding 2097148k swap on /mnt/md0/.swapfile. Priority:-1 extents:2 across:2228220k
[ 49.680611] ---ug_sys_log_monitor.sh sleep 10,before uptime 60 second
[ 53.820318] [RTK_VE1] before pctrl_on for laterncy watching!!
[ 53.846797] [RTK_VE1] after pctrl_on for laterncy watching!!
[ 54.276304] [RTK_VE1] before pctrl_on for laterncy watching!!
[ 54.282289] [RTK_VE1] after pctrl_on for laterncy watching!!
[ 55.491080] xunlei-pan-cli is runing!,Sat Feb 1 09:23:20 CST 2025
[ 59.737384] ---ug_sys_log_monitor.sh sleep 10,before uptime 60 second
[ 69.787154] ---SYS_LOG_FILE:/data/nas_server/log/system/HB316F032200FEBC_20250201092302_syslog
root@UGREEN-38CA:~# cd /data/nas_server/log/system/
root@UGREEN-38CA:/data/nas_server/log/system# ll
drwxrwxrwx 3 root root 4096 Feb 1 09:23 ./
drwxrwxrwx 5 root root 61440 Feb 1 09:25 ../
-rwxrwxrwx 1 root root 105372 Jan 31 22:24 HB316F032200FEBC_20250131222346_syslog*
-rwxrwxrwx 1 root root 80533 Jan 31 22:27 HB316F032200FEBC_20250131222637_syslog*
-rwxrwxrwx 1 root root 205127 Feb 1 08:45 HB316F032200FEBC_20250131222811_syslog*
-rwxrwxrwx 1 root root 109337 Feb 1 08:48 HB316F032200FEBC_20250201084617_syslog*
-rwxrwxrwx 1 root root 105090 Feb 1 08:54 HB316F032200FEBC_20250201085252_syslog*
-rwxrwxrwx 1 root root 106862 Feb 1 09:25 HB316F032200FEBC_20250201092302_syslog*
drwxrwxrwx 2 root root 4096 Dec 29 2022 crash/
root@UGREEN-38CA:/data/nas_server/log/system# grep -inr ssda ./* | grep erroir
root@UGREEN-38CA:/data/nas_server/log/system# grep -inr ssda ./* | grep error
root@UGREEN-38CA:/data/nas_server/log/system# ll
drwxrwxrwx 3 root root 4096 Feb 1 09:23 ./
drwxrwxrwx 5 root root 61440 Feb 1 09:25 ../
-rwxrwxrwx 1 root root 105372 Jan 31 22:24 HB316F032200FEBC_20250131222346_syslog*
-rwxrwxrwx 1 root root 80533 Jan 31 22:27 HB316F032200FEBC_20250131222637_syslog*
-rwxrwxrwx 1 root root 205127 Feb 1 08:45 HB316F032200FEBC_20250131222811_syslog*
-rwxrwxrwx 1 root root 109337 Feb 1 08:48 HB316F032200FEBC_20250201084617_syslog*
-rwxrwxrwx 1 root root 105090 Feb 1 08:54 HB316F032200FEBC_20250201085252_syslog*
-rwxrwxrwx 1 root root 106862 Feb 1 09:25 HB316F032200FEBC_20250201092302_syslog*
drwxrwxrwx 2 root root 4096 Dec 29 2022 crash/
root@UGREEN-38CA:/data/nas_server/log/system# vi HB316F032200FEBC_20250131222637_syslog
root@UGREEN-38CA:/data/nas_server/log/system# ll
drwxrwxrwx 3 root root 4096 Feb 1 09:23 ./
drwxrwxrwx 5 root root 61440 Feb 1 09:25 ../
-rwxrwxrwx 1 root root 105372 Jan 31 22:24 HB316F032200FEBC_20250131222346_syslog*
-rwxrwxrwx 1 root root 80533 Jan 31 22:27 HB316F032200FEBC_20250131222637_syslog*
-rwxrwxrwx 1 root root 205127 Feb 1 08:45 HB316F032200FEBC_20250131222811_syslog*
-rwxrwxrwx 1 root root 109337 Feb 1 08:48 HB316F032200FEBC_20250201084617_syslog*
-rwxrwxrwx 1 root root 105090 Feb 1 08:54 HB316F032200FEBC_20250201085252_syslog*
-rwxrwxrwx 1 root root 109722 Feb 1 09:26 HB316F032200FEBC_20250201092302_syslog*
drwxrwxrwx 2 root root 4096 Dec 29 2022 crash/
root@UGREEN-38CA:/data/nas_server/log/system# vi HB316F032200FEBC_20250131222811_syslog
root@UGREEN-38CA:/data/nas_server/log/system# vi HB316F032200FEBC_20250201092302_syslog
root@UGREEN-38CA:/data/nas_server/log/system# vi HB316F032200FEBC_20250201085252_syslog
root@UGREEN-38CA:/data/nas_server/log/system# grep -A 6 -inr "lsblk" ./*
./HB316F032200FEBC_20250131222346_syslog:1114:-------------------lsblk:
./HB316F032200FEBC_20250131222346_syslog-1115-NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
./HB316F032200FEBC_20250131222346_syslog-1116-mmcblk0 179:0 0 7.3G 0 disk
./HB316F032200FEBC_20250131222346_syslog-1117-|-mmcblk0p1 179:1 0 1G 0 part /rom
./HB316F032200FEBC_20250131222346_syslog-1118-`-mmcblk0p2 179:2 0 5.2G 0 part /overlay
./HB316F032200FEBC_20250131222346_syslog-1119-mmcblk0boot0 179:8 0 4M 1 disk
./HB316F032200FEBC_20250131222346_syslog-1120-mmcblk0boot1 179:16 0 4M 1 disk
--
./HB316F032200FEBC_20250131222811_syslog:1122:-------------------lsblk:
./HB316F032200FEBC_20250131222811_syslog-1123-NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
./HB316F032200FEBC_20250131222811_syslog-1124-sda 8:0 0 5.5T 0 disk
./HB316F032200FEBC_20250131222811_syslog-1125-`-sda1 8:1 0 5.5T 0 part
./HB316F032200FEBC_20250131222811_syslog-1126- `-md0 9:0 0 5.5T 0 raid1 /mnt/md0
./HB316F032200FEBC_20250131222811_syslog-1127-mmcblk0 179:0 0 7.3G 0 disk
./HB316F032200FEBC_20250131222811_syslog-1128-|-mmcblk0p1 179:1 0 1G 0 part /rom
--
./HB316F032200FEBC_20250201084617_syslog:1147:-------------------lsblk:
./HB316F032200FEBC_20250201084617_syslog-1148-NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
./HB316F032200FEBC_20250201084617_syslog-1149-sda 8:0 0 5.5T 0 disk
./HB316F032200FEBC_20250201084617_syslog-1150-`-sda1 8:1 0 5.5T 0 part
./HB316F032200FEBC_20250201084617_syslog-1151- `-md0 9:0 0 5.5T 0 raid1 /mnt/md0
./HB316F032200FEBC_20250201084617_syslog-1152-mmcblk0 179:0 0 7.3G 0 disk
./HB316F032200FEBC_20250201084617_syslog-1153-|-mmcblk0p1 179:1 0 1G 0 part /rom
--
./HB316F032200FEBC_20250201085252_syslog:1115:-------------------lsblk:
./HB316F032200FEBC_20250201085252_syslog-1116-NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
./HB316F032200FEBC_20250201085252_syslog-1117-sda 8:0 0 5.5T 0 disk
./HB316F032200FEBC_20250201085252_syslog-1118-`-sda1 8:1 0 5.5T 0 part
./HB316F032200FEBC_20250201085252_syslog-1119- `-md0 9:0 0 5.5T 0 raid1 /mnt/md0
./HB316F032200FEBC_20250201085252_syslog-1120-mmcblk0 179:0 0 7.3G 0 disk
./HB316F032200FEBC_20250201085252_syslog-1121-|-mmcblk0p1 179:1 0 1G 0 part /rom
--
./HB316F032200FEBC_20250201092302_syslog:1132:-------------------lsblk:
./HB316F032200FEBC_20250201092302_syslog-1133-NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
./HB316F032200FEBC_20250201092302_syslog-1134-sda 8:0 0 5.5T 0 disk
./HB316F032200FEBC_20250201092302_syslog-1135-`-sda1 8:1 0 5.5T 0 part
./HB316F032200FEBC_20250201092302_syslog-1136- `-md0 9:0 0 5.5T 0 raid1 /mnt/md0
./HB316F032200FEBC_20250201092302_syslog-1137-mmcblk0 179:0 0 7.3G 0 disk
./HB316F032200FEBC_20250201092302_syslog-1138-|-mmcblk0p1 179:1 0 1G 0 part /rom
root@UGREEN-38CA:/data/nas_server/log/system# grep -A 15 -inr "lsblk" ./*
./HB316F032200FEBC_20250131222346_syslog:1114:-------------------lsblk:
./HB316F032200FEBC_20250131222346_syslog-1115-NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
./HB316F032200FEBC_20250131222346_syslog-1116-mmcblk0 179:0 0 7.3G 0 disk
./HB316F032200FEBC_20250131222346_syslog-1117-|-mmcblk0p1 179:1 0 1G 0 part /rom
./HB316F032200FEBC_20250131222346_syslog-1118-`-mmcblk0p2 179:2 0 5.2G 0 part /overlay
./HB316F032200FEBC_20250131222346_syslog-1119-mmcblk0boot0 179:8 0 4M 1 disk
./HB316F032200FEBC_20250131222346_syslog-1120-mmcblk0boot1 179:16 0 4M 1 disk
./HB316F032200FEBC_20250131222346_syslog-1121-mmcblk0rpmb 179:24 0 512K 0 disk
./HB316F032200FEBC_20250131222346_syslog-1122--------------------route -n:
./HB316F032200FEBC_20250131222346_syslog-1123-Kernel IP routing table
./HB316F032200FEBC_20250131222346_syslog-1124-Destination Gateway Genmask Flags Metric Ref Use Iface
./HB316F032200FEBC_20250131222346_syslog-1125-0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth0
./HB316F032200FEBC_20250131222346_syslog-1126-192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
./HB316F032200FEBC_20250131222346_syslog-1127--------------------ifconfig -a:
./HB316F032200FEBC_20250131222346_syslog-1128-bond0 Link encap:Ethernet HWaddr 92:FC:32:2A:44:17
./HB316F032200FEBC_20250131222346_syslog-1129- BROADCAST MASTER MULTICAST MTU:1500 Metric:1
--
./HB316F032200FEBC_20250131222811_syslog:1122:-------------------lsblk:
./HB316F032200FEBC_20250131222811_syslog-1123-NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
./HB316F032200FEBC_20250131222811_syslog-1124-sda 8:0 0 5.5T 0 disk
./HB316F032200FEBC_20250131222811_syslog-1125-`-sda1 8:1 0 5.5T 0 part
./HB316F032200FEBC_20250131222811_syslog-1126- `-md0 9:0 0 5.5T 0 raid1 /mnt/md0
./HB316F032200FEBC_20250131222811_syslog-1127-mmcblk0 179:0 0 7.3G 0 disk
./HB316F032200FEBC_20250131222811_syslog-1128-|-mmcblk0p1 179:1 0 1G 0 part /rom
./HB316F032200FEBC_20250131222811_syslog-1129-`-mmcblk0p2 179:2 0 5.2G 0 part /overlay
./HB316F032200FEBC_20250131222811_syslog-1130-mmcblk0boot0 179:8 0 4M 1 disk
./HB316F032200FEBC_20250131222811_syslog-1131-mmcblk0boot1 179:16 0 4M 1 disk
./HB316F032200FEBC_20250131222811_syslog-1132-mmcblk0rpmb 179:24 0 512K 0 disk
./HB316F032200FEBC_20250131222811_syslog-1133--------------------route -n:
./HB316F032200FEBC_20250131222811_syslog-1134-Kernel IP routing table
./HB316F032200FEBC_20250131222811_syslog-1135-Destination Gateway Genmask Flags Metric Ref Use Iface
./HB316F032200FEBC_20250131222811_syslog-1136-0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth0
./HB316F032200FEBC_20250131222811_syslog-1137-192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
--
./HB316F032200FEBC_20250201084617_syslog:1147:-------------------lsblk:
./HB316F032200FEBC_20250201084617_syslog-1148-NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
./HB316F032200FEBC_20250201084617_syslog-1149-sda 8:0 0 5.5T 0 disk
./HB316F032200FEBC_20250201084617_syslog-1150-`-sda1 8:1 0 5.5T 0 part
./HB316F032200FEBC_20250201084617_syslog-1151- `-md0 9:0 0 5.5T 0 raid1 /mnt/md0
./HB316F032200FEBC_20250201084617_syslog-1152-mmcblk0 179:0 0 7.3G 0 disk
./HB316F032200FEBC_20250201084617_syslog-1153-|-mmcblk0p1 179:1 0 1G 0 part /rom
./HB316F032200FEBC_20250201084617_syslog-1154-`-mmcblk0p2 179:2 0 5.2G 0 part /overlay
./HB316F032200FEBC_20250201084617_syslog-1155-mmcblk0boot0 179:8 0 4M 1 disk
./HB316F032200FEBC_20250201084617_syslog-1156-mmcblk0boot1 179:16 0 4M 1 disk
./HB316F032200FEBC_20250201084617_syslog-1157-mmcblk0rpmb 179:24 0 512K 0 disk
./HB316F032200FEBC_20250201084617_syslog-1158--------------------route -n:
./HB316F032200FEBC_20250201084617_syslog-1159-Kernel IP routing table
./HB316F032200FEBC_20250201084617_syslog-1160-Destination Gateway Genmask Flags Metric Ref Use Iface
./HB316F032200FEBC_20250201084617_syslog-1161-0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth0
./HB316F032200FEBC_20250201084617_syslog-1162-192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
--
./HB316F032200FEBC_20250201085252_syslog:1115:-------------------lsblk:
./HB316F032200FEBC_20250201085252_syslog-1116-NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
./HB316F032200FEBC_20250201085252_syslog-1117-sda 8:0 0 5.5T 0 disk
./HB316F032200FEBC_20250201085252_syslog-1118-`-sda1 8:1 0 5.5T 0 part
./HB316F032200FEBC_20250201085252_syslog-1119- `-md0 9:0 0 5.5T 0 raid1 /mnt/md0
./HB316F032200FEBC_20250201085252_syslog-1120-mmcblk0 179:0 0 7.3G 0 disk
./HB316F032200FEBC_20250201085252_syslog-1121-|-mmcblk0p1 179:1 0 1G 0 part /rom
./HB316F032200FEBC_20250201085252_syslog-1122-`-mmcblk0p2 179:2 0 5.2G 0 part /overlay
./HB316F032200FEBC_20250201085252_syslog-1123-mmcblk0boot0 179:8 0 4M 1 disk
./HB316F032200FEBC_20250201085252_syslog-1124-mmcblk0boot1 179:16 0 4M 1 disk
./HB316F032200FEBC_20250201085252_syslog-1125-mmcblk0rpmb 179:24 0 512K 0 disk
./HB316F032200FEBC_20250201085252_syslog-1126--------------------route -n:
./HB316F032200FEBC_20250201085252_syslog-1127-Kernel IP routing table
./HB316F032200FEBC_20250201085252_syslog-1128-Destination Gateway Genmask Flags Metric Ref Use Iface
./HB316F032200FEBC_20250201085252_syslog-1129-0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth0
./HB316F032200FEBC_20250201085252_syslog-1130-192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
--
./HB316F032200FEBC_20250201092302_syslog:1132:-------------------lsblk:
./HB316F032200FEBC_20250201092302_syslog-1133-NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
./HB316F032200FEBC_20250201092302_syslog-1134-sda 8:0 0 5.5T 0 disk
./HB316F032200FEBC_20250201092302_syslog-1135-`-sda1 8:1 0 5.5T 0 part
./HB316F032200FEBC_20250201092302_syslog-1136- `-md0 9:0 0 5.5T 0 raid1 /mnt/md0
./HB316F032200FEBC_20250201092302_syslog-1137-mmcblk0 179:0 0 7.3G 0 disk
./HB316F032200FEBC_20250201092302_syslog-1138-|-mmcblk0p1 179:1 0 1G 0 part /rom
./HB316F032200FEBC_20250201092302_syslog-1139-`-mmcblk0p2 179:2 0 5.2G 0 part /overlay
./HB316F032200FEBC_20250201092302_syslog-1140-mmcblk0boot0 179:8 0 4M 1 disk
./HB316F032200FEBC_20250201092302_syslog-1141-mmcblk0boot1 179:16 0 4M 1 disk
./HB316F032200FEBC_20250201092302_syslog-1142-mmcblk0rpmb 179:24 0 512K 0 disk
./HB316F032200FEBC_20250201092302_syslog-1143--------------------route -n:
./HB316F032200FEBC_20250201092302_syslog-1144-Kernel IP routing table
./HB316F032200FEBC_20250201092302_syslog-1145-Destination Gateway Genmask Flags Metric Ref Use Iface
./HB316F032200FEBC_20250201092302_syslog-1146-0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth0
./HB316F032200FEBC_20250201092302_syslog-1147-192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
root@UGREEN-38CA:/data/nas_server/log/system#
root@UGREEN-38CA:/data/nas_server/log/system#
root@UGREEN-38CA:/data/nas_server/log/system#
root@UGREEN-38CA:/data/nas_server/log/system#
root@UGREEN-38CA:/data/nas_server/log/system#
root@UGREEN-38CA:/data/nas_server/log/system#
root@UGREEN-38CA:/data/nas_server/log/system#
root@UGREEN-38CA:/data/nas_server/log/system# smartctl -ai /dev/sda
smartctl 7.2 2020-12-30 r5155 [aarch64-linux-4.9.119] (localbuild)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: ST6000NM0024-1HT17Z
Serial Number: Z4D3EQ84
LU WWN Device Id: 5 000c50 0877e5030
Add. Product Id: DELL(tm)
Firmware Version: MA29
User Capacity: 6,001,175,126,016 bytes [6.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-3 (minor revision not indicated)
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sat Feb 1 09:31:00 2025 CST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 90) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 626) minutes.
Conveyance self-test routine
recommended polling time: ( 3) minutes.
SCT capabilities: (0x50bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x010f 077 064 --- Pre-fail Always - 50655880
3 Spin_Up_Time 0x0103 087 085 --- Pre-fail Always - 0
4 Start_Stop_Count 0x0032 099 099 --- Old_age Always - 1032
5 Reallocated_Sector_Ct 0x0133 100 100 --- Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 078 077 --- Pre-fail Always - 83075630
9 Power_On_Hours 0x0032 091 091 --- Old_age Always - 8257
10 Spin_Retry_Count 0x0013 100 100 --- Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 --- Old_age Always - 56
184 End-to-End_Error 0x0032 100 100 --- Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 --- Old_age Always - 0
188 Command_Timeout 0x0032 100 099 --- Old_age Always - 8590065666
189 High_Fly_Writes 0x003a 100 100 --- Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 063 047 --- Old_age Always - 37 (Min/Max 34/37)
191 G-Sense_Error_Rate 0x0032 100 100 --- Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 --- Old_age Always - 31
193 Load_Cycle_Count 0x0032 100 100 --- Old_age Always - 273
194 Temperature_Celsius 0x0022 037 053 --- Old_age Always - 37 (0 11 0 0 0)
195 Hardware_ECC_Recovered 0x001a 008 006 --- Old_age Always - 50655880
196 Reallocated_Event_Count 0x0032 000 000 --- Old_age Always - 0
197 Current_Pending_Sector 0x0012 100 100 --- Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 --- Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 --- Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 --- Old_age Offline - 414 (228 160 0)
241 Total_LBAs_Written 0x0000 100 253 --- Old_age Offline - 3936451489
242 Total_LBAs_Read 0x0000 100 253 --- Old_age Offline - 9203453618
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 8257 -
# 2 Short offline Completed without error 00% 8002 -
# 3 Short offline Completed without error 00% 7530 -
# 4 Short offline Completed without error 00% 3659 -
# 5 Short offline Completed without error 00% 3587 -
# 6 Short offline Completed without error 00% 3515 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
root@UGREEN-38CA:/data/nas_server/log/system# client_loop: send disconnect: Connection reset
C:\Users\Administrator>ssh -p 922 root@192.168.2.150
ssh: connect to host 192.168.2.150 port 922: Connection refused
C:\Users\Administrator>ssh -p 922 root@192.168.2.150
ssh: connect to host 192.168.2.150 port 922: Connection refused
C:\Users\Administrator>ssh -p 922 root@192.168.2.150
root@192.168.2.150's password:
Permission denied, please try again.
root@192.168.2.150's password:
BusyBox v1.28.3 () built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
UGOS 18.06-SNAPSHOT,
-----------------------------------------------------
root@UGREEN-38CA:~# lsblk
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
sda 8:0 0 5.5T 0 disk
└─sda1 8:1 0 5.5T 0 part
└─md0 9:0 0 5.5T 0 raid1 /mnt/md0
mmcblk0 179:0 0 7.3G 0 disk
├─mmcblk0p1 179:1 0 1G 0 part /rom
└─mmcblk0p2 179:2 0 5.2G 0 part /overlay
mmcblk0boot0 179:8 0 4M 1 disk
mmcblk0boot1 179:16 0 4M 1 disk
mmcblk0rpmb 179:24 0 512K 0 disk
root@UGREEN-38CA:~# smartctl -ai /dev/sda
smartctl 7.2 2020-12-30 r5155 [aarch64-linux-4.9.119] (localbuild)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: ST6000NM0024-1HT17Z
Serial Number: Z4D3EQ1G
LU WWN Device Id: 5 000c50 0877e61a1
Add. Product Id: DELL(tm)
Firmware Version: MA29
User Capacity: 6,001,175,126,016 bytes [6.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-3 (minor revision not indicated)
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sat Feb 1 09:33:58 2025 CST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 90) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 638) minutes.
Conveyance self-test routine
recommended polling time: ( 3) minutes.
SCT capabilities: (0x50bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x010f 078 063 --- Pre-fail Always - 66923584
3 Spin_Up_Time 0x0103 089 085 --- Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 --- Old_age Always - 391
5 Reallocated_Sector_Ct 0x0133 100 100 --- Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 078 077 --- Pre-fail Always - 83320392
9 Power_On_Hours 0x0032 091 091 --- Old_age Always - 8497
10 Spin_Retry_Count 0x0013 100 100 --- Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 --- Old_age Always - 59
184 End-to-End_Error 0x0032 100 100 --- Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 --- Old_age Always - 0
188 Command_Timeout 0x0032 100 099 --- Old_age Always - 4295032833
189 High_Fly_Writes 0x003a 100 100 --- Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 072 047 --- Old_age Always - 28 (Min/Max 27/28)
191 G-Sense_Error_Rate 0x0032 100 100 --- Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 --- Old_age Always - 33
193 Load_Cycle_Count 0x0032 100 100 --- Old_age Always - 333
194 Temperature_Celsius 0x0022 028 053 --- Old_age Always - 28 (0 11 0 0 0)
195 Hardware_ECC_Recovered 0x001a 007 006 --- Old_age Always - 66923584
196 Reallocated_Event_Count 0x0032 000 000 --- Old_age Always - 0
197 Current_Pending_Sector 0x0012 100 100 --- Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 --- Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 --- Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 --- Old_age Offline - 469 (127 241 0)
241 Total_LBAs_Written 0x0000 100 253 --- Old_age Offline - 10538545891
242 Total_LBAs_Read 0x0000 100 253 --- Old_age Offline - 4062120585
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 8252 -
# 2 Short offline Completed without error 00% 7639 -
# 3 Short offline Completed without error 00% 3750 -
# 4 Short offline Completed without error 00% 3679 -
# 5 Short offline Completed without error 00% 3607 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
root@UGREEN-38CA:~#
root@UGREEN-38CA:~#
root@UGREEN-38CA:~#
root@UGREEN-38CA:~#
root@UGREEN-38CA:~#
root@UGREEN-38CA:~#
root@UGREEN-38CA:~# ll
drwxr-xr-x 1 root root 4096 May 29 2022 ./
drwxr-xr-x 1 root root 4096 Sep 14 11:27 ../
drwxr-xr-x 2 root root 4096 May 29 2022 .drive/
drwxr-xr-x 3 root root 4096 Jan 1 2021 download/
drwxr-xr-x 2 root root 192 Apr 8 2024 fio/
drwxr-xr-x 2 root root 50 Apr 8 2024 utils/
root@UGREEN-38CA:~# ll
drwxr-xr-x 1 root root 4096 May 29 2022 ./
drwxr-xr-x 1 root root 4096 Sep 14 11:27 ../
drwxr-xr-x 2 root root 4096 May 29 2022 .drive/
drwxr-xr-x 3 root root 4096 Jan 1 2021 download/
drwxr-xr-x 2 root root 192 Apr 8 2024 fio/
drwxr-xr-x 2 root root 50 Apr 8 2024 utils/
root@UGREEN-38CA:~# dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.9.119 (ugreen@jenkins-ugos) (gcc version 8.2.0 (OpenWrt GCC 8.2.0 ) ) #0 SMP PREEMPT Mon Apr 8 13:55:47 2024
[ 0.000000] Boot CPU: AArch64 Processor [410fd034]
[ 0.000000] DT: logo_start_addr 0x30000000, size 0x900000
[ 0.000000] DT: free_logo_reserved_region 0
[ 0.000000] DT: saving_section_page_table 0
[ 0.000000] earlycon: uart8250 at MMIO32 0x0000000098007800 (options '')
[ 0.000000] bootconsole [uart8250] enabled
[ 0.000000] rsvmem_remap_setup 234, not remap common@0 now
[ 0.000000] rsvmem_remap_setup 234, not remap ringbuf@0 now
[ 0.000000] rsvmem_remap_setup 234, not remap rbus@0 now
[ 0.000000] cma: size 0x0000000002000000, base 0x0000000000000000, fixed(0)
[ 0.000000] cma: Reserved 32 MiB at 0x000000007e000000
[ 0.000000] On node 0 totalpages: 523776
[ 0.000000] DMA zone: 8192 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 523776 pages, LIFO batch:31
[ 0.000000] percpu: Embedded 22 pages/cpu @ffffffc07df5f000 s52376 r8192 d29544 u90112
[ 0.000000] pcpu-alloc: s52376 r8192 d29544 u90112 alloc=22*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: enabling workaround for ARM erratum 845719
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 515584
[ 0.000000] Kernel command line: earlycon=uart8250,mmio32,0x98007800 console=ttyS0,115200 U-boot=2015.07-45f6c71 (May 12 2021 - 16:47:00) init=/etc/init root=/dev/mmcblk0p1 rootfstype=squashfs overlay=/dev/mmcblk0p2 overlayfs=ext4 rootwait loglevel=8
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Memory: 1553200K/2095104K available (7678K kernel code, 1058K rwdata, 4152K rodata, 3392K init, 415K bss, 509136K reserved, 32768K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB)
[ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB)
[ 0.000000] .text : 0xffffff8008280000 - 0xffffff8008a00000 ( 7680 KB)
[ 0.000000] .rodata : 0xffffff8008a00000 - 0xffffff8008e20000 ( 4224 KB)
[ 0.000000] .init : 0xffffff8008e20000 - 0xffffff8009170000 ( 3392 KB)
[ 0.000000] .data : 0xffffff8009170000 - 0xffffff8009278808 ( 1059 KB)
[ 0.000000] .bss : 0xffffff8009278808 - 0xffffff80092e046c ( 416 KB)
[ 0.000000] fixed : 0xffffffbefe7fb000 - 0xffffffbefec00000 ( 4116 KB)
[ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB)
[ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum)
[ 0.000000] 0xffffffbf00000000 - 0xffffffbf02000000 ( 32 MB actual)
[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc080000000 ( 2048 MB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] CONFIG_RCU_FANOUT set to non-default value of 32
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 27.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x63a1e71a3, max_idle_ns: 440795203123 ns
[ 0.000006] sched_clock: 56 bits at 27MHz, resolution 37ns, wraps every 4398046511093ns
[ 0.009092] [RTK-TIMER0] set mode: shutdown
[ 0.013798] [RTK-TIMER0] clocksource 0 register HZ
[ 0.019189] clocksource: rtk_timer0_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 70787423951 ns
[ 0.030782] [RTK-TIMER1] clocksource 1 register HZ
[ 0.036171] clocksource: rtk_timer1_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 70787423951 ns
[ 0.047949] rmem_count: 4
[ 0.051866]
[ 0.053536] rsvmem_remap 143, rmem->name common@0
[ 0.059807] rsvmem_remap 151, type rsvmem-remap
[ 0.065880] rsvmem_remap 163, ioremap(1f000,1000)
[ 0.072151] rsvmem_remap 175, remap addr ffffff800800c000
[ 0.079204] rsvmem_remap 184, save_remap_name common
[ 0.085764] rsvmem_remap 203, save rpc_common_base
[ 0.092128] rsvmem_remap 216, init common@0/common done
[ 0.098979]
[ 0.100647] rsvmem_remap 143, rmem->name ringbuf@0
[ 0.107014] rsvmem_remap 151, type rsvmem-remap
[ 0.113086] rsvmem_remap 163, ioremap(1ffe000,4000)
[ 0.119555] rsvmem_remap 175, remap addr ffffff8008010000
[ 0.126608] rsvmem_remap 184, save_remap_name ringbuf
[ 0.133265] rsvmem_remap 210, save rpc_ringbuf_base
[ 0.139729] rsvmem_remap 216, init ringbuf@0/ringbuf done
[ 0.146777]
[ 0.148446] rsvmem_remap 143, rmem->name ramoops@0
[ 0.154812] rsvmem_remap 151, type ramoops
[ 0.160396] rsvmem_remap 154, value is not match
[ 0.166562]
[ 0.168232] rsvmem_remap 143, rmem->name rbus@0
[ 0.174303] rsvmem_remap 151, type rsvmem-remap
[ 0.180376] rsvmem_remap 163, ioremap(98000000,200000)
[ 0.187136] rsvmem_remap 175, remap addr ffffff8009400000
[ 0.194186] rsvmem_remap 184, save_remap_name rbus
[ 0.200550] rsvmem_remap 188, save rbus_addr
[ 0.206331] rsvmem_remap 195, set rtk_rbus_barrier_flag to 1
[ 0.213673] rsvmem_remap 216, init rbus@0/rbus done
[ 0.220526] Console: colour dummy device 80x25
[ 0.225555] Calibrating delay loop (skipped), value calculated using timer frequency.. 54.00 BogoMIPS (lpj=108000)
[ 0.237233] pid_max: default: 32768 minimum: 301
[ 0.242628] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.250191] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.258897] ftrace: allocating 29761 entries in 117 pages
[ 0.323696] sched-energy: CPU device node has no sched-energy-costs
[ 0.330800] Invalid sched_group_energy for CPU0
[ 0.335912] CPU0: update cpu_capacity 1024
[ 0.340553] ASID allocator initialised with 32768 entries
[ 0.427005] Detected VIPT I-cache on CPU1
[ 0.427059] Invalid sched_group_energy for CPU1
[ 0.427062] CPU1: update cpu_capacity 1024
[ 0.427066] CPU1: Booted secondary processor [410fd034]
[ 0.459070] Detected VIPT I-cache on CPU2
[ 0.459103] Invalid sched_group_energy for CPU2
[ 0.459106] CPU2: update cpu_capacity 1024
[ 0.459110] CPU2: Booted secondary processor [410fd034]
[ 0.491163] Detected VIPT I-cache on CPU3
[ 0.491195] Invalid sched_group_energy for CPU3
[ 0.491198] CPU3: update cpu_capacity 1024
[ 0.491201] CPU3: Booted secondary processor [410fd034]
[ 0.491281] Brought up 4 CPUs
[ 0.554997] SMP: Total of 4 processors activated.
[ 0.560305] CPU features: detected feature: 32-bit EL0 Support
[ 0.566883] CPU features: detected feature: Kernel page table isolation (KPTI)
[ 0.577946] CPU: All CPU(s) started at EL2
[ 0.582585] alternatives: patching kernel code
[ 0.587802] Invalid sched_group_energy for CPU3
[ 0.592918] Invalid sched_group_energy for Cluster3
[ 0.598420] Invalid sched_group_energy for CPU2
[ 0.603529] Invalid sched_group_energy for Cluster2
[ 0.609028] Invalid sched_group_energy for CPU1
[ 0.614135] Invalid sched_group_energy for Cluster1
[ 0.619637] Invalid sched_group_energy for CPU0
[ 0.624747] Invalid sched_group_energy for Cluster0
[ 0.630778] devtmpfs: initialized
[ 0.645994] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.656998] futex hash table entries: 1024 (order: 5, 131072 bytes)
[ 0.665529] pinctrl core: initialized pinctrl subsystem
[ 0.672130] NET: Registered protocol family 16
[ 0.689187] cpuidle: using governor ladder
[ 0.709846] cpuidle: using governor menu
[ 0.714688] vdso: 2 pages (1 code @ ffffff8008a06000, 1 data @ ffffff8009174000)
[ 0.723043] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.731386] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.738612] rst-control : base ffffff8008060600, offset 0x40
[ 0.745013] ****** rtk_lockapi_init 620, chip: id=0x00000000, revision=0x00030000
[ 0.753454] ****** rtk_lockapi_init 627, bypass mode
[ 0.759713] pstore: using zlib compression
[ 0.764347] pstore: Registered ramoops as persistent store backend
[ 0.771322] ramoops: attached 0x200000@0x22000000, ecc: 0/0
[ 0.778198] rtk-mmio 98000000.mmio: use hw semaphore
[ 0.783906] rtk-cgc 9800000c.clk-en: initialized
[ 0.789372] rtk-cgc 98000010.clk-en: initialized
[ 0.794723] rtk-cgc 98000450.clk-en: initialized
[ 0.800084] rtk-mmio 98007088.mmio: use hw semaphore
[ 0.805766] rtk-cgc 9800708c.clk-en: initialized
[ 0.811113] rtk-rtd129x-cc 98000000.clock-controller: use mmio regmap
[ 0.818632] rtk-rtd129x-cc 98000000.clock-controller: initialized
[ 0.825649] rtk-reset 98000000.soft-reset: use mmio regmap
[ 0.831847] rtk-reset 98000000.soft-reset: initialized
[ 0.837775] rtk-reset 98000000.shadow-soft-reset: use mmio regmap
[ 0.844661] rtk-reset 98000000.shadow-soft-reset: initialized
[ 0.851274] rtk-reset 98000004.soft-reset: use mmio regmap
[ 0.857471] rtk-reset 98000004.soft-reset: initialized
[ 0.863397] rtk-reset 98000008.soft-reset: use mmio regmap
[ 0.869594] rtk-reset 98000008.soft-reset: initialized
[ 0.875522] rtk-reset 98000050.soft-reset: use mmio regmap
[ 0.881721] rtk-reset 98000050.soft-reset: initialized
[ 0.887647] rtk-reset 98007088.soft-reset: use mmio regmap
[ 0.893845] rtk-reset 98007088.soft-reset: initialized
[ 0.899771] rtk-reset 98000000.async-soft-reset: use mmio regmap
[ 0.906555] rtk-reset 98000000.async-soft-reset: initialized
[ 0.913070] rtk-reset 98000004.async-soft-reset: use mmio regmap
[ 0.919855] rtk-reset 98000004.async-soft-reset: initialized
[ 0.926539] rtk-rtd129x-power 98000000.power-controller: initialized
[ 0.933863] [PINCTRL] driver init
[ 0.940163] [PINCTRL] init done
[ 0.946191] [RTK_DCSYS_DBG] DC_EC_CTRL(0x98008300) = 7000000
[ 0.952600] [RTK_DCSYS_DBG] initialized
[ 0.962247] [GPIO] No default gpio need to set
[ 0.970758] [RTK_SB2_DBG] sb2_dbg_probe
[ 0.975146] [RTK_SB2_DBG] info 0x30000
[ 0.979379] [RTK_SB2_DBG] use smc 0
[ 1.008422] ACPI: Interpreter disabled.
[ 1.012800] [RTD129x_PM] Initial Power Management Driver
[ 1.019161] [RTD129x_PM] wakeup-gpio Cnt: en(2) act(2) list(2)
[ 1.025760] [RTD129x_PM] wakeup-gpio[0] States is disable!
[ 1.031753] (en:0 act:1 gpio:115)
[ 1.035622] [RTD129x_PM] wakeup-gpio[1] Successful registration!
[ 1.042201] (en:1 act:0 gpio:134)
[ 1.046033] [RTD129x_PM] gpio-output-change Cnt: en(0) act(0) list(-2)
[ 1.053396] [RTD129x_PM] Wakeup Flags Set Default : 0x2c
[ 1.059387] [RTD129x_PM] as system-power-controller
[ 1.064971] rtk-usb-manager 98000000.rtk_usb_power_manager: ENTER rtk_usb_manager_probe
[ 1.074037] rtk-usb-manager 98000000.rtk_usb_power_manager: parse_gpio_setting get power-gpio (id=102) OK
[ 1.084847] rtk-usb-manager 98000000.rtk_usb_power_manager: parse_gpio_setting get power-gpio (id=132) OK
[ 1.095658] rtk-usb-manager 98000000.rtk_usb_power_manager: parse_gpio_setting get power-gpio (id=133) OK
[ 1.106468] mac_node: rtk_dwc3_drd status is okay
[ 1.111774] type_c_node: rtk_dwc3_drd_type_c status is okay
[ 1.118067] rtk-usb-manager 98000000.rtk_usb_power_manager: __of_parse_port_gpio_mapping port0 mapping gpio_num=102
[ 1.129853] mac_node: rtk_dwc3_u2host status is okay
[ 1.135464] rtk-usb-manager 98000000.rtk_usb_power_manager: __of_parse_port_gpio_mapping port1 mapping gpio_num=132
[ 1.147252] mac_node: ehci status is okay
[ 1.151777] slave_mac_node: ohci status is okay
[ 1.156897] rtk-usb-manager 98000000.rtk_usb_power_manager: __of_parse_port_gpio_mapping port2 mapping gpio_num=132
[ 1.168681] mac_node: rtk_dwc3_u3host status is okay
[ 1.174289] rtk-usb-manager 98000000.rtk_usb_power_manager: __of_parse_port_gpio_mapping port3 mapping gpio_num=133
[ 1.186061] rtk_usb_soc_init START (drivers/soc/realtek/rtd129x/rtk_usb.c)
[ 1.193857] rtk_usb_iso_power_ctrl power_on ([0x98007fb0=0x0f000073)
[ 1.201027] set usb_power_domain/p3 on
[ 1.205264] set power_domain on ([0x98007fb0]=0x0f000073)
[ 1.211910] rtk-usb-manager 98000000.rtk_usb_power_manager: Realtek USB init OK
[ 1.220186] rtk-usb-manager 98000000.rtk_usb_power_manager: __gpio_on_off to set power off by gpio (id=102) OK
[ 1.231493] rtk-usb-manager 98000000.rtk_usb_power_manager: __gpio_on_off to set power off by gpio (id=132) OK
[ 1.242797] rtk-usb-manager 98000000.rtk_usb_power_manager: __gpio_on_off to set power off by gpio (id=133) OK
[ 1.254180] rtk-usb-manager 98000000.rtk_usb_power_manager: create_debug_files
[ 1.262375] rtk-usb-manager 98000000.rtk_usb_power_manager: rtk_usb_manager_probe OK (take 196 ms)
[ 1.272871] SCSI subsystem initialized
[ 1.277138] libata version 3.00 loaded.
[ 1.281556] usbcore: registered new interface driver usbfs
[ 1.287789] usbcore: registered new interface driver hub
[ 1.293856] usbcore: registered new device driver usb
[ 1.299975] rtk-efuse 98017000.efuse: initialized
[ 1.305481] Advanced Linux Sound Architecture Driver Initialized.
[ 1.313398] clocksource: Switched to clocksource arch_sys_counter
[ 1.349096] VFS: Disk quotas dquot_6.6.0
[ 1.353598] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.361512] FS-Cache: Loaded
[ 1.364817] pnp: PnP ACPI: disabled
[ 1.369040] drivers/soc/realtek/common/rtk_ion_of.c rtk_ion_probe
[ 1.376925] drivers/soc/realtek/common/rtk_ion_of.c rtk_ion_probe nr_heaps:5
[ 1.388809] rtk_ion_probe: adding heap Audio of type 8 with 2600000@800000 (type:GEN_POOL)
[ 1.534055] rtk_ion_probe: adding heap Media of type 7 with 7e000000@2000000 (type:CMA_POOL)
[ 1.544564] rtk_ion_probe: adding heap Media of type 7 with 12000000@d500000 (type:GEN_POOL)
[ 1.555074] rtk_ion_probe: adding heap Media of type 7 with 2e00000@d200000 (type:GEN_POOL)
[ 1.573618] NET: Registered protocol family 2
[ 1.579087] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 1.587394] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[ 1.595151] TCP: Hash tables configured (established 16384 bind 16384)
[ 1.602566] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 1.609407] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 1.616870] NET: Registered protocol family 1
[ 1.622122] RPC: Registered named UNIX socket transport module.
[ 1.628808] RPC: Registered udp transport module.
[ 1.634116] RPC: Registered tcp transport module.
[ 1.639422] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.646693] PCI: CLS 0 bytes, default 128
[ 1.651674] Failed to device reset: -2
[ 1.656209] Failed to device reset: -2
[ 1.660617] Failed to device reset: -2
[ 1.665039] Failed to device reset: -2
[ 1.669549] Failed to device reset: -2
[ 1.673953] Failed to device reset: -2
[ 1.682008] Crashlog allocated RAM at address 0x3f00000
[ 1.688119] workingset: timestamp_bits=46 max_order=19 bucket_order=0
[ 1.696296] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.703129] FS-Cache: Netfs 'nfs' registered for caching
[ 1.709335] NFS: Registering the id_resolver key type
[ 1.715053] Key type id_resolver registered
[ 1.719781] Key type id_legacy registered
[ 1.724320] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.732230] Key type cifs.idmap registered
[ 1.738471] NET: Registered protocol family 38
[ 1.743549] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 1.751908] io scheduler noop registered
[ 1.756344] io scheduler deadline registered
[ 1.761236] io scheduler cfq registered (default)
[ 1.766769] phy-rtk-sata 9803ff00.sata_phy: can't find rx table
[ 1.773573] phy-rtk-sata 9803ff00.sata_phy: can't find rx table
[ 1.780593] [RTK_PWM] rtd1295_pwm_probe - hwpwm=(0) enable=(0) duty_rate=(5) clksrc_div=(1) clkout_div=(255)---
[ 1.792182] [RTK_PWM] rtd1295_pwm_probe - defualt output frequence = 26367Hz ---
[ 1.800731] [RTK_PWM] rtd1295_pwm_probe - hwpwm=(1) enable=(1) duty_rate=(50) clksrc_div=(1) clkout_div=(255)---
[ 1.812416] [RTK_PWM] rtd1295_pwm_probe - defualt output frequence = 26367Hz ---
[ 1.820965] [RTK_PWM] rtd1295_pwm_probe - hwpwm=(2) enable=(0) duty_rate=(50) clksrc_div=(1) clkout_div=(255)---
[ 1.832640] [RTK_PWM] rtd1295_pwm_probe - defualt output frequence = 26367Hz ---
[ 1.841185] [RTK_PWM] rtd1295_pwm_probe - hwpwm=(3) enable=(0) duty_rate=(50) clksrc_div=(1) clkout_div=(255)---
[ 1.852859] [RTK_PWM] rtd1295_pwm_probe - defualt output frequence = 26367Hz ---
[ 1.861506] 980070d0.pwm.0: failed to get pinctrl: -19
[ 1.867447] 980070d0.pwm.1: failed to get pinctrl: -19
[ 1.873411] 980070d0.pwm.2: failed to get pinctrl: -19
[ 1.880659] misc rtk_lockapi: registered.
[ 1.885203] [PUWRAP] begin pu_init
[ 1.889041] [PUWRAP] end pu_init result=0x0
[ 1.893866] [PUWRAP] pu_probe
[ 1.897232] [PUWRAP] success to probe pu wrapper device with USE_ION_ALLOCATOR
[ 1.905568] [RTK_VE1] vpu_probe
[ 1.909120] [RTK_VE1] vpu base address get from DTB physical base addr=0x98040000, virtual base=0xffffff8008270000, size=0x8000
[ 1.922210] [RTK_VE1] res.start:0x98007000, bonding_value:0x0
[ 1.928797] [RTK_VE1] s_ve1_irq:22 want to register ve1_irq_handler
[ 1.935921] [RTK_VE1] s_ve2_irq:23 want to register ve2_irq_handler
[ 1.943021] [RTK_VE1] success to probe vpu device with non reserved video memory
[ 1.951578] [RTK_VE3] base address get from DTB physical base addr=0x98048000, virtual base=0xffffff80092e8000, size=0x4000(actually=0x424)
[ 1.965859] [RTK_VE3] get clock controller s_ve3_clk=0xffffffc07ad84880
[ 1.973330] ve3_pctrl_on
[ 1.985419] [RTK_VE3] Get cti: 0x13
[ 1.989345] [RTK_VE3] dec kernel module
[ 1.993678] [RTK_VE3] Init single core at 0x 98048000 IRQ=24
[ 2.000749] [RTK_VE3] core[0] has HEVC
[ 2.004979] [RTK_VE3] core[0] has VP9
[ 2.009111] [RTK_VE3] core[0] has PP
[ 2.013331] [RTK_VE3] module inserted. Major = 0
[ 2.018554] ve3_pctrl_off
[ 2.021578] memalloc: Linear Memory Allocator
[ 2.026740] [RTK_JPU] jpu_probe
[ 2.030312] [RTK_JPU] jpu base address get from DTB physical base addr=0x9803e000, virtual base=0xffffff80081c9000, size=0x1000
[ 2.043388] [RTK_JPU] get clock controller s_jpu_clk=0xffffffc07ad84080
[ 2.050884] [RTK_JPU] s_jpu_irq:21 want to register jpu_irq_handler
[ 2.057986] [RTK_JPU] success to probe jpu device with non reserved video memory
[ 2.066400] [RTK_JPU] jpu_init
[ 2.069850] [RTK_JPU] end jpu_init result=0x0
[ 2.075115] [RTK_RPC] rpc driver initial begin
[ 2.080254] [RTK_RPC]rpc is not paused & suspended
[ 2.087552] [RTK_RPC] rpc_int_base:ffffff80081e9104
[ 2.093062] [RTK_RPC] acpu_irq:27
[ 2.096830] [RTK_RPC] rpc driver initial done
[ 2.101933] [RTK MCP] MCP driver initial begin.
[ 2.107068] [RTK MCP] MCP Base: 0xffffff80081f1000
[ 2.112475] [RTK MCP] TP Base: 0xffffff80081f9000
[ 2.117908] [RTK MCP] MCP driver initial done.
[ 2.123498] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 2.131937] console [ttyS0] disabled
[ 2.285001] 98007800.serial0: ttyS0 at MMIO 0x98007800 (irq = 194, base_baud = 1687500) is a 16550A
[ 2.295249] console [ttyS0] enabled
[ 2.302764] bootconsole [uart8250] disabled
[ 2.312206] 9801b200.serial1: ttyS1 at MMIO 0x9801b200 (irq = 163, base_baud = 27000000) is a 16550A
[ 2.331420] brd: module loaded
[ 2.336561] g2227 0-0012: g2227 rev219
[ 2.345576] g2227-regulator g2227-regulator: initialized
[ 2.351050] g2227 0-0012: initialized
[ 2.355889] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x1111
[ 2.361712] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x5111
[ 2.367526] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x9111
[ 2.373338] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x336a0511
[ 2.379505] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x336a4511
[ 2.385673] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x336a8511
[ 2.391840] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0xe0700111
[ 2.398007] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0xe05c4111
[ 2.404175] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0xe04a8111
[ 2.410343] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x150611
[ 2.416332] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x154611
[ 2.422321] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x158611
[ 2.428310] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0xc6000a11
[ 2.434476] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0xc6004a11
[ 2.440644] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0xc6008a11
[ 2.446811] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x70000211
[ 2.452978] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x70004211
[ 2.459145] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x70008211
[ 2.465313] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0xc6600a11
[ 2.471480] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0xc6604a11
[ 2.477647] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0xc6608a11
[ 2.483814] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x20041911
[ 2.489981] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x20045911
[ 2.496147] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x20049911
[ 2.502315] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x94aa2011
[ 2.508482] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x94aa6011
[ 2.514650] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x94aaa011
[ 2.520816] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x17171511
[ 2.526984] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x17175511
[ 2.533151] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x17179511
[ 2.539318] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x7701611
[ 2.545404] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x7705611
[ 2.551483] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x7709611
[ 2.557561] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x40002a11
[ 2.563729] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x40006a11
[ 2.569895] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x4000aa11
[ 2.576062] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x29001011
[ 2.582236] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x29005011
[ 2.588404] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x29009011
[ 2.594572] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x40000c11
[ 2.600739] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x40004c11
[ 2.606906] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x40008c11
[ 2.613074] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x271711
[ 2.619064] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x275711
[ 2.625053] phy-rtk-sata 9803ff00.sata_phy: phy0 para 0x279711
[ 2.631043] phy-rtk-sata 9803ff00.sata_phy: phy0 txdrv 0x94a72011
[ 2.637300] phy-rtk-sata 9803ff00.sata_phy: phy0 txdrv 0x94a76011
[ 2.643555] phy-rtk-sata 9803ff00.sata_phy: phy0 txdrv 0x94a7a011
[ 2.649811] phy-rtk-sata 9803ff00.sata_phy: phy0 txdrv 0x587a2111
[ 2.656067] phy-rtk-sata 9803ff00.sata_phy: phy0 txdrv 0x587a6111
[ 2.662323] phy-rtk-sata 9803ff00.sata_phy: phy0 txdrv 0x587aa111
[ 2.668580] phy-rtk-sata 9803ff00.sata_phy: phy0 rxsense 0x42100911
[ 2.675013] phy-rtk-sata 9803ff00.sata_phy: phy0 rxsense 0x42104911
[ 2.681447] phy-rtk-sata 9803ff00.sata_phy: phy0 rxsense 0x42108911
[ 2.687881] phy-rtk-sata 9803ff00.sata_phy: phy0 rxsense 0x276f0311
[ 2.694315] phy-rtk-sata 9803ff00.sata_phy: phy0 rxsense 0x276d4311
[ 2.700749] phy-rtk-sata 9803ff00.sata_phy: phy0 rxsense 0x276d8311
[ 2.707215] phy-rtk-sata 9803ff00.sata_phy: init phy0 OK
[ 2.712672] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x1111
[ 2.718484] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x5111
[ 2.724294] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x9111
[ 2.730105] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x336a0511
[ 2.736272] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x336a4511
[ 2.742438] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x336a8511
[ 2.748606] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0xe0700111
[ 2.754773] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0xe05c4111
[ 2.760940] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0xe04a8111
[ 2.767107] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x150611
[ 2.773096] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x154611
[ 2.779085] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x158611
[ 2.785073] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0xc6000a11
[ 2.791241] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0xc6004a11
[ 2.797408] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0xc6008a11
[ 2.803575] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x70000211
[ 2.809742] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x70004211
[ 2.815910] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x70008211
[ 2.822076] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0xc6600a11
[ 2.828243] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0xc6604a11
[ 2.834410] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0xc6608a11
[ 2.840584] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x20041911
[ 2.846752] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x20045911
[ 2.852919] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x20049911
[ 2.859086] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x94aa2011
[ 2.865253] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x94aa6011
[ 2.871420] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x94aaa011
[ 2.877587] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x17171511
[ 2.883754] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x17175511
[ 2.889921] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x17179511
[ 2.896088] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x7701611
[ 2.902167] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x7705611
[ 2.908245] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x7709611
[ 2.914324] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x40002a11
[ 2.920489] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x40006a11
[ 2.926657] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x4000aa11
[ 2.932824] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x29001011
[ 2.938991] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x29005011
[ 2.945158] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x29009011
[ 2.951325] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x40000c11
[ 2.957492] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x40004c11
[ 2.963660] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x40008c11
[ 2.969828] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x271711
[ 2.975818] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x275711
[ 2.981807] phy-rtk-sata 9803ff00.sata_phy: phy1 para 0x279711
[ 2.987796] phy-rtk-sata 9803ff00.sata_phy: phy1 txdrv 0x94a72011
[ 2.994052] phy-rtk-sata 9803ff00.sata_phy: phy1 txdrv 0x94a76011
[ 3.000308] phy-rtk-sata 9803ff00.sata_phy: phy1 txdrv 0x94a7a011
[ 3.006564] phy-rtk-sata 9803ff00.sata_phy: phy1 txdrv 0x587a2111
[ 3.012819] phy-rtk-sata 9803ff00.sata_phy: phy1 txdrv 0x587a6111
[ 3.019075] phy-rtk-sata 9803ff00.sata_phy: phy1 txdrv 0x587aa111
[ 3.025331] phy-rtk-sata 9803ff00.sata_phy: phy1 rxsense 0x42100911
[ 3.031765] phy-rtk-sata 9803ff00.sata_phy: phy1 rxsense 0x42104911
[ 3.038198] phy-rtk-sata 9803ff00.sata_phy: phy1 rxsense 0x42108911
[ 3.044632] phy-rtk-sata 9803ff00.sata_phy: phy1 rxsense 0x276f0311
[ 3.051065] phy-rtk-sata 9803ff00.sata_phy: phy1 rxsense 0x276d4311
[ 3.057499] phy-rtk-sata 9803ff00.sata_phy: phy1 rxsense 0x276d8311
[ 3.063964] phy-rtk-sata 9803ff00.sata_phy: init phy1 OK
[ 3.069623] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[ 3.077873] r8169 Gigabit Ethernet driver 2.6.0LK-NAPI loaded
[ 3.094191] r8169 98016000.gmac eth0: RTL8168g/8111g at 0xffffff8008241000, XID 10900800 IRQ 17
[ 3.103125] r8169 98016000.gmac eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[ 3.112042] [Ethernet] Watch link status change.
[ 3.112437] rtk-uio 98000000.rbus: initialized
[ 3.112623] rtk-uio 9801b000.refclk: initialized
[ 3.116913] rtk-se 9800c000.se: irq=15
[ 3.116922] rtk-se 9800c000.se: phys:0x000000009800c000 virt:0xffffff8008259000 size:0x0000000000001000 type:1 name:SE reg space
[ 3.116931] rtk-se 9800c000.se: phys:0x000000007e040000 virt:0xffffff800826e000 size:0x0000000000001000 type:1 name:SE driver data
[ 3.116939] rtk-se 9800c000.se: phys:0x000000007e048000 virt:0xffffff8009386000 size:0x0000000000008000 type:1 name:SE command queue
[ 3.117179] rtk-se 9800c000.se: [SE] Engine[0] Ctrl:00000001 Base:7e048000 ReadPtr:7e048000 WritePtr:7e048000 Limit:7e04c000
[ 3.117189] rtk-se 9800c000.se: [SE] Engine[1] Ctrl:00000001 Base:7e04c000 ReadPtr:7e04c000 WritePtr:7e04c000 Limit:7e050000
[ 3.117195] rtk-se 9800c000.se: shared mode
[ 3.117200] rtk-se 9800c000.se: initialized
[ 3.117509] rtk-md 9800b000.md: irq=14
[ 3.117518] rtk-md 9800b000.md: phys:0x000000009800b000 virt:0xffffff8008279000 size:0x0000000000001000 type:1 name:MD reg space
[ 3.117526] rtk-md 9800b000.md: phys:0x000000007e041000 virt:0xffffff800827b000 size:0x0000000000001000 type:1 name:MD driver data
[ 3.117534] rtk-md 9800b000.md: phys:0x000000007e044000 virt:0xffffff800938f000 size:0x0000000000004000 type:1 name:MD command queue
[ 3.117770] rtk-md 9800b000.md: [MD] Engine[0] Ctrl:00000005 Base:7e044000 ReadPtr:7e044000 WritePtr:7e044000 Limit:7e048000
[ 3.117777] rtk-md 9800b000.md: shared mode
[ 3.117782] rtk-md 9800b000.md: initialized
[ 3.117994] rtk-usb-phy-rle0599 98013824.usb_phy_rle0599: rtk_usb_rle0599_phy_probe: Chip 1296 revision is b01
[ 3.118034] rtk-usb-phy-rle0599 98013824.usb_phy_rle0599: Probe RTK USB 2.0 RLE0599 PHY
[ 3.118277] rtk-usb2phy 98028280.dwc3_drd_usb2phy: rtk_usb2phy_probe: Chip 1296 revision is b01
[ 3.118340] rtk-usb2phy 98028280.dwc3_drd_usb2phy: drivers/usb/phy/phy-rtk-usb2.c Probe RTK USB 2.0 PHY
[ 3.118386] rtk-usb2phy 98031280.dwc3_u2host_usb2phy: rtk_usb2phy_probe: Chip 1296 revision is b01
[ 3.118429] rtk-usb2phy 98031280.dwc3_u2host_usb2phy: drivers/usb/phy/phy-rtk-usb2.c Probe RTK USB 2.0 PHY
[ 3.118485] rtk-usb2phy 981f8280.dwc3_u3host_usb2phy: rtk_usb2phy_probe: Chip 1296 revision is b01
[ 3.118538] rtk-usb2phy 981f8280.dwc3_u3host_usb2phy: drivers/usb/phy/phy-rtk-usb2.c Probe RTK USB 2.0 PHY
[ 3.118796] rtk-usb3phy 98013210.dwc3_drd_usb3phy: rtk_usb3phy_probe: Chip 1296 revision is b01
[ 3.118823] rtk-usb3phy 98013210.dwc3_drd_usb3phy: rtk_usb3phy_probe load phy_data_revA parameter
[ 3.118853] rtk-usb3phy 98013210.dwc3_drd_usb3phy: drivers/usb/phy/phy-rtk-usb3.c Probe RTK USB 3.0 PHY
[ 3.118913] rtk-usb3phy 98013e10.dwc3_u3host_usb3phy: rtk_usb3phy_probe: Chip 1296 revision is b01
[ 3.118936] rtk-usb3phy 98013e10.dwc3_u3host_usb3phy: rtk_usb3phy_probe load phy_data_revA parameter
[ 3.118958] rtk-usb3phy 98013e10.dwc3_u3host_usb3phy: drivers/usb/phy/phy-rtk-usb3.c Probe RTK USB 3.0 PHY
[ 3.119648] rtk-dwc3 98013200.rtk_dwc3_drd: Probe Realtek-SoC USB DWC3 Host Controller
[ 3.119925] rtk-usb-manager 98000000.rtk_usb_power_manager: rtk_usb_manager_schedule_work for 98013200.rtk_dwc3_drd
[ 3.119942] rtk-dwc3 98013200.rtk_dwc3_drd: dwc3_rtk_probe ok! (take 0 ms)
[ 3.119952] rtk-dwc3 98013200.rtk_dwc3_drd: dwc3_rtk_probe_work Start ...
[ 3.119979] rtk-dwc3 98013c00.rtk_dwc3_u2host: Probe Realtek-SoC USB DWC3 Host Controller
[ 3.120229] rtk-usb-manager 98000000.rtk_usb_power_manager: rtk_usb_manager_schedule_work for 98013c00.rtk_dwc3_u2host
[ 3.120247] rtk-dwc3 98013c00.rtk_dwc3_u2host: dwc3_rtk_probe ok! (take 0 ms)
[ 3.120289] dwc3 98020000.dwc3_drd: rtk dwc3 fixed dwc3 globals register start address 0xffffff80093d8100
[ 3.120307] rtk-dwc3 98013e00.rtk_dwc3_u3host: Probe Realtek-SoC USB DWC3 Host Controller
[ 3.120456] rtk-usb2phy 98028280.dwc3_drd_usb2phy: rtk_usb2_phy_init Init RTK USB 2.0 PHY
[ 3.120463] rtk-usb2phy 98028280.dwc3_drd_usb2phy: do_rtk_usb2_phy_init Init RTK USB 2.0 PHY phy#0
[ 3.120509] rtk-usb2phy 98028280.dwc3_drd_usb2phy: do_rtk_usb2_phy_toggle ########## to toggle Page1 addr 0xe0 BIT(2)
[ 3.120551] rtk-usb-manager 98000000.rtk_usb_power_manager: rtk_usb_manager_schedule_work for 98013e00.rtk_dwc3_u3host
[ 3.120565] rtk-dwc3 98013e00.rtk_dwc3_u3host: dwc3_rtk_probe ok! (take 0 ms)
[ 3.121021] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.121031] ehci-pci: EHCI PCI platform driver
[ 3.121079] ehci-rtk: EHCI realtek driver init
[ 3.121169] rtk-ehci 98013000.ehci: Probe Realtek-SoC USB EHCI Host Controller
[ 3.121227] rtk-ehci 98013000.ehci: ehci_rtk_drv_probe Enable fixed_async_list_addr_bug
[ 3.121273] rtk-usb-manager 98000000.rtk_usb_power_manager: rtk_usb_manager_schedule_work for 98013000.ehci
[ 3.121288] rtk-ehci 98013000.ehci: ehci_rtk_drv_probe OK (take 0 ms)
[ 3.121451] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.121526] rtk-usb2phy 98028280.dwc3_drd_usb2phy: do_rtk_usb2_phy_toggle disconnect to set Page0 0xE7 = f1
[ 3.121533] rtk-usb2phy 98028280.dwc3_drd_usb2phy: rtk_usb2_phy_init Initialized RTK USB 2.0 PHY (take 0ms)
[ 3.121539] rtk-usb3phy 98013210.dwc3_drd_usb3phy: rtk_usb_phy_init Init RTK USB 3.0 PHY
[ 3.121545] rtk-usb3phy 98013210.dwc3_drd_usb3phy: do_rtk_usb_phy_init Init RTK USB 3.0 PHY phy#0
[ 3.121549] rtk-ohci 98013400.ohci: Probe Realtek-SoC USB OHCI Host Controller
[ 3.121649] rtk-usb-manager 98000000.rtk_usb_power_manager: rtk_usb_manager_schedule_work for 98013400.ohci
[ 3.121662] rtk-ohci 98013400.ohci: ohci_rtk_drv_probe OK (take 0 ms)
[ 3.121806] ohci-pci: OHCI PCI platform driver
[ 3.122330] usbcore: registered new interface driver usb-storage
[ 3.122371] usbcore: registered new interface driver ums-realtek
[ 3.122512] [RTK_RTC] 9801b600.rtc: rtk_base_year = 2016
[ 3.122689] [RTK_RTC] 9801b600.rtc: rtk_rtc rtcacr = 0x80
[ 3.122696] [RTK_RTC] 9801b600.rtc: rtk_rtc already enabled
[ 3.122703] [RTK_RTC] 9801b600.rtc: enable REG_SEC = 0x61
[ 3.122708] [RTK_RTC] 9801b600.rtc: enable REG_MIN = 0x1d
[ 3.122713] [RTK_RTC] 9801b600.rtc: enable REG_HR = 0xb
[ 3.122719] [RTK_RTC] 9801b600.rtc: enable REG_DATA_LOW = 0x0
[ 3.122724] [RTK_RTC] 9801b600.rtc: enable REG_DATE_HIGH = 0x0
[ 3.122943] [RTK_RTC] 9801b600.rtc: rtc core: registered rtc as rtc0
[ 3.122948] [RTK_RTC] 9801b600.rtc: initialized
[ 3.123015] i2c /dev entries driver
[ 3.127399] rtk-usb3phy 98013210.dwc3_drd_usb3phy: do_rtk_usb3_phy_toggle ########## to toggle PHY addr 0x09 BIT(9)
[ 3.128709] rtk-usb3phy 98013210.dwc3_drd_usb3phy: do_rtk_usb3_phy_toggle ########## PHY addr 0x1f = 0x70081f10
[ 3.128716] rtk-usb3phy 98013210.dwc3_drd_usb3phy: rtk_usb_phy_init Initialized RTK USB 3.0 PHY (take 8ms)
[ 3.128758] dwc3 98020000.dwc3_drd: dwc3_gadget_init Enter
[ 3.129125] dwc3 98020000.dwc3_drd: dwc3_gadget_init Exit
[ 3.129748] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: ENTER dwc3_rtk_type_c_probe
[ 3.129768] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: No mapping memory for type_c_reg_base!
[ 3.129774] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: Let type_c_reg_base = ffffff80093f434c
[ 3.129858] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: dwc3_rtk_type_c_probe get rd_ctrl-gpio (id=135) OK
[ 3.129866] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: Set device mode boot_check_time -1 ms ==> (Disable to check)
[ 3.129873] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: Set filter_config_channel_signal is False
[ 3.129883] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: Chip 1296 revision is b01 (support revision a01) to load A01 parameter
[ 3.129942] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: DWC3_DRD is DRD mode
[ 3.129989] rtk-usb-manager 98000000.rtk_usb_power_manager: rtk_usb_manager_schedule_work for 98013200.rtk_dwc3_drd_type_c
[ 3.130008] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: create_debug_files
[ 3.130044] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: Exit dwc3_rtk_type_c_probe OK (take 4 ms)
[ 3.130091] rtk-dwc3 98013200.rtk_dwc3_drd: dwc3_rtk_probe_work End ... ok! (take 12 ms)
[ 3.130099] rtk-dwc3 98013c00.rtk_dwc3_u2host: dwc3_rtk_probe_work Start ...
[ 3.130353] dwc3 98029000.dwc3_u2host: rtk dwc3 fixed dwc3 globals register start address 0xffffff8009618100
[ 3.130460] rtk-usb2phy 98031280.dwc3_u2host_usb2phy: rtk_usb2_phy_init Init RTK USB 2.0 PHY
[ 3.130467] rtk-usb2phy 98031280.dwc3_u2host_usb2phy: do_rtk_usb2_phy_init Init RTK USB 2.0 PHY phy#0
[ 3.130514] rtk-usb2phy 98031280.dwc3_u2host_usb2phy: do_rtk_usb2_phy_toggle ########## to toggle Page1 addr 0xe0 BIT(2)
[ 3.131529] rtk-usb2phy 98031280.dwc3_u2host_usb2phy: do_rtk_usb2_phy_toggle disconnect to set Page0 0xE7 = f1
[ 3.131535] rtk-usb2phy 98031280.dwc3_u2host_usb2phy: rtk_usb2_phy_init Initialized RTK USB 2.0 PHY (take 0ms)
[ 3.131570] dwc3 98029000.dwc3_u2host: dwc3_host_init
[ 3.131743] xhci-hcd xhci-hcd.6.auto: xHCI Host Controller
[ 3.131763] xhci-hcd xhci-hcd.6.auto: new USB bus registered, assigned bus number 1
[ 3.132011] xhci-hcd xhci-hcd.6.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x02010010
[ 3.132046] xhci-hcd xhci-hcd.6.auto: irq 9, io mem 0x98029000
[ 3.132746] hub 1-0:1.0: USB hub found
[ 3.132777] hub 1-0:1.0: 1 port detected
[ 3.133049] xhci-hcd xhci-hcd.6.auto: xHCI Host Controller
[ 3.133061] xhci-hcd xhci-hcd.6.auto: new USB bus registered, assigned bus number 2
[ 3.133131] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.133711] hub 2-0:1.0: USB hub found
[ 3.133739] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 3.134034] rtk-usb-manager 98000000.rtk_usb_power_manager: rtk_usb_init_port_power_on for 98013c00.rtk_dwc3_u2host
[ 3.134044] rtk-usb-manager 98000000.rtk_usb_power_manager: __usb_port_power_on_off port1 power=on enable=0x1 enable_mask=0x1
[ 3.134052] rtk-usb-manager 98000000.rtk_usb_power_manager: gpio_num=132 enable_port=0x2 enable_port_mask=0x6 ==> No turn on
[ 3.134060] rtk-dwc3 98013c00.rtk_dwc3_u2host: dwc3_rtk_probe_work End ... ok! (take 4 ms)
[ 3.134068] rtk-dwc3 98013e00.rtk_dwc3_u3host: dwc3_rtk_probe_work Start ...
[ 3.134326] dwc3 981f0000.dwc3_u3host: rtk dwc3 fixed dwc3 globals register start address 0xffffff8009648100
[ 3.134478] rtk-usb2phy 981f8280.dwc3_u3host_usb2phy: rtk_usb2_phy_init Init RTK USB 2.0 PHY
[ 3.134485] rtk-usb2phy 981f8280.dwc3_u3host_usb2phy: do_rtk_usb2_phy_init Init RTK USB 2.0 PHY phy#0
[ 3.134537] rtk-usb2phy 981f8280.dwc3_u3host_usb2phy: do_rtk_usb2_phy_toggle ########## to toggle Page1 addr 0xe0 BIT(2)
[ 3.135552] rtk-usb2phy 981f8280.dwc3_u3host_usb2phy: do_rtk_usb2_phy_toggle disconnect to set Page0 0xE7 = f1
[ 3.135559] rtk-usb2phy 981f8280.dwc3_u3host_usb2phy: rtk_usb2_phy_init Initialized RTK USB 2.0 PHY (take 0ms)
[ 3.135565] rtk-usb3phy 98013e10.dwc3_u3host_usb3phy: rtk_usb_phy_init Init RTK USB 3.0 PHY
[ 3.135571] rtk-usb3phy 98013e10.dwc3_u3host_usb3phy: do_rtk_usb_phy_init Init RTK USB 3.0 PHY phy#0
[ 3.141440] rtk-usb3phy 98013e10.dwc3_u3host_usb3phy: do_rtk_usb3_phy_toggle ########## to toggle PHY addr 0x09 BIT(9)
[ 3.142751] rtk-usb3phy 98013e10.dwc3_u3host_usb3phy: do_rtk_usb3_phy_toggle ########## PHY addr 0x1f = 0x90001f10
[ 3.142757] rtk-usb3phy 98013e10.dwc3_u3host_usb3phy: rtk_usb_phy_init Initialized RTK USB 3.0 PHY (take 8ms)
[ 3.142794] dwc3 981f0000.dwc3_u3host: dwc3_host_init
[ 3.142953] xhci-hcd xhci-hcd.7.auto: xHCI Host Controller
[ 3.142970] xhci-hcd xhci-hcd.7.auto: new USB bus registered, assigned bus number 3
[ 3.143228] xhci-hcd xhci-hcd.7.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x02010010
[ 3.143245] xhci-hcd xhci-hcd.7.auto: irq 9, io mem 0x981f0000
[ 3.143853] hub 3-0:1.0: USB hub found
[ 3.143880] hub 3-0:1.0: 1 port detected
[ 3.144136] xhci-hcd xhci-hcd.7.auto: xHCI Host Controller
[ 3.144148] xhci-hcd xhci-hcd.7.auto: new USB bus registered, assigned bus number 4
[ 3.144215] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.144745] hub 4-0:1.0: USB hub found
[ 3.144773] hub 4-0:1.0: 1 port detected
[ 3.145146] rtk-usb-manager 98000000.rtk_usb_power_manager: rtk_usb_init_port_power_on for 98013e00.rtk_dwc3_u3host
[ 3.145155] rtk-usb-manager 98000000.rtk_usb_power_manager: __usb_port_power_on_off port3 power=on enable=0x1 enable_mask=0x1
[ 3.145196] rtk-usb-manager 98000000.rtk_usb_power_manager: __gpio_on_off to set power on by gpio (id=133) OK
[ 3.145207] rtk-dwc3 98013e00.rtk_dwc3_u3host: dwc3_rtk_probe_work End ... ok! (take 8 ms)
[ 3.145214] rtk-ehci 98013000.ehci: ehci_rtk_probe_work Start ...
[ 3.145221] rtk-usb-phy-rle0599 98013824.usb_phy_rle0599: Init RTK USB phy-rle0599
[ 3.145306] rtk-usb-phy-rle0599 98013824.usb_phy_rle0599: rtk_rle0599_phy_toggle ########## to toggle Page1 addr 0xe0 BIT(2)
[ 3.146317] rtk-usb-phy-rle0599 98013824.usb_phy_rle0599: drivers/usb/phy/phy-rtk-rle0599.c Initialized RTK USB PHY rle0599
[ 3.146342] rtk-ehci 98013000.ehci: EHCI Host Controller
[ 3.146361] rtk-ehci 98013000.ehci: new USB bus registered, assigned bus number 5
[ 3.146500] rtk-ehci 98013000.ehci: irq 9, io mem 0x98013000
[ 3.150518] rtk-thermal-sensor 9801d150.thermal-sensor: initialized
[ 3.157431] rtk-ehci 98013000.ehci: USB 2.0 started, EHCI 1.00
[ 3.158040] hub 5-0:1.0: USB hub found
[ 3.158069] hub 5-0:1.0: 1 port detected
[ 3.158365] rtk-usb-manager 98000000.rtk_usb_power_manager: rtk_usb_init_port_power_on for 98013000.ehci
[ 3.158374] rtk-usb-manager 98000000.rtk_usb_power_manager: __usb_port_power_on_off port2 power=on enable=0x1 enable_mask=0x3
[ 3.158380] rtk-ehci 98013000.ehci: ehci_rtk_probe_work End ... ok! (take 16 ms)
[ 3.158388] rtk-ohci 98013400.ohci: ohci_rtk_probe_work Start ...
[ 3.158396] rtk-ohci 98013400.ohci: Rtk Dmp OHCI
[ 3.158413] rtk-ohci 98013400.ohci: new USB bus registered, assigned bus number 6
[ 3.158426] rtk-ohci 98013400.ohci: _ohci_readl [USB Workaround] fixed force to enable ohci clock
[ 3.159552] rtk-ohci 98013400.ohci: irq 9, io mem 0x98013400
[ 3.176644] rtk-thermal-sensor 980124b4.thermal-sensor: initialized
[ 3.177672] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com
[ 3.178319] EMMC : emmc of_node found
[ 3.178392] [rtkemmc_probe] get speed-step : 2
[ 3.178397] [rtkemmc_probe] no driving nf_s1 warning !!
[ 3.178401] [rtkemmc_probe] get driving s2 : 0x1
[ 3.178403] [rtkemmc_probe] get driving s2 : 0xbb
[ 3.178406] [rtkemmc_probe] get driving s2 : 0xbb
[ 3.178408] [rtkemmc_probe] get driving s2 : 0xbb
[ 3.178411] [rtkemmc_probe] get driving s2 : 0x33
[ 3.178414] [rtkemmc_probe] no driving nf_s3 warning !!
[ 3.178418] [rtkemmc_probe] get tx tuning switch : 0
[ 3.178420] [rtkemmc_probe] get rx tuning switch : 0
[ 3.178423] [rtkemmc_probe] no dqs_tuning switch node !!
[ 3.178426] [rtkemmc_probe] no tx & rx reference phase switch node !!
[ 3.178430] [rtkemmc_probe] No emmc tuning offset node, using MBR format !!
[ 3.178520] rtkemmc_set_pin_mux: EMMC_PFUNC_NF1 = 0x33333333
[ 3.178551] EMMC: set to 0x00000000, EMMC_CTYPE=00000000
[ 3.178559] EMMC: set_wrapper_div to 0x00002100
[ 3.178563] EMMC, set_ip_div = cur_div(0x00000080), ignored.
[ 3.179207] EMMC: set_freq to 0x46, EMMC_CKGEN_CTL=0x00002100, PLL_EMMC1=00000003, PLL_EMMC2=04517893, PLL_EMMC3=00464388, PLL_EMMC4=00000007
[ 3.179726] EMMC: set_freq to 0x46, EMMC_CKGEN_CTL=0x00002100, PLL_EMMC1=00000003, PLL_EMMC2=04517893, PLL_EMMC3=00464388, PLL_EMMC4=00000007
[ 3.179729] EMMC, set_ip_div = cur_div(0x00000080), ignored.
[ 3.197841] EMMC: set_freq to 0x46, EMMC_CKGEN_CTL=0x00002100, PLL_EMMC1=00000003, PLL_EMMC2=04517893, PLL_EMMC3=00464388, PLL_EMMC4=00000007
[ 3.197845] EMMC, set_ip_div = cur_div(0x00000080), ignored.
[ 3.217480] mmc0: EMMC driver initialized
[ 3.217921] EMMC: set_freq to 0x46, EMMC_CKGEN_CTL=0x00002100, PLL_EMMC1=00000003, PLL_EMMC2=04517893, PLL_EMMC3=00464388, PLL_EMMC4=00000007
[ 3.217925] EMMC, set_ip_div = cur_div(0x00000080), ignored.
[ 3.221251] EMMC: set_freq to 0x46, EMMC_CKGEN_CTL=0x00002100, PLL_EMMC1=00000003, PLL_EMMC2=04517893, PLL_EMMC3=00464388, PLL_EMMC4=00000007
[ 3.221254] EMMC, set_ip_div = cur_div(0x00000080), ignored.
[ 3.222031] hub 6-0:1.0: USB hub found
[ 3.222065] hub 6-0:1.0: 1 port detected
[ 3.222358] rtk-usb-manager 98000000.rtk_usb_power_manager: rtk_usb_init_port_power_on for 98013400.ohci
[ 3.222367] rtk-usb-manager 98000000.rtk_usb_power_manager: __usb_port_power_on_off port2 power=on enable=0x3 enable_mask=0x3
[ 3.222405] rtk-usb-manager 98000000.rtk_usb_power_manager: __gpio_on_off to set power on by gpio (id=132) OK
[ 3.222415] rtk-ohci 98013400.ohci: ohci_rtk_probe_work End ... ok! (take 64 ms)
[ 3.222424] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: dwc3_rtk_type_c_probe_work Start ...
[ 3.222433] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: dwc3_rtk_type_c_init set debounce = 0x7f (check--> 0xff)
[ 3.222454] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: rtk_type_c_init
[ 3.222500] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: switch_dwc3_mode dr_mode=0
[ 3.222506] dwc3 98020000.dwc3_drd: dwc3_drd_to_stop_all START....
[ 3.222512] dwc3 98020000.dwc3_drd: dwc3_gadget_exit Enter
[ 3.222658] dwc3 98020000.dwc3_drd: dwc3_gadget_exit Exit
[ 3.222663] dwc3 98020000.dwc3_drd: dwc3_drd_to_stop_all END....
[ 3.222670] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: DWC3_DRD run in USB_DR_MODE_PERIPHERAL at DRD mode
[ 3.222675] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: First time device mode check is Diable
[ 3.222688] EMMC: set_freq to 0x46, EMMC_CKGEN_CTL=0x00002100, PLL_EMMC1=00000003, PLL_EMMC2=04517893, PLL_EMMC3=00464388, PLL_EMMC4=00000007
[ 3.222691] EMMC, set_ip_div = cur_div(0x00000080), ignored.
[ 3.222699] rtk-dwc3-type_c 98013200.rtk_dwc3_drd_type_c: dwc3_rtk_type_c_probe_work End ... ok! (take 0 ms)
[ 3.226325] EMMC: set_freq to 0x46, EMMC_CKGEN_CTL=0x00002100, PLL_EMMC1=00000003, PLL_EMMC2=04517893, PLL_EMMC3=00464388, PLL_EMMC4=00000007
[ 3.226329] EMMC, set_ip_div = cur_div(0x00000080), ignored.
[ 3.226758] EMMC: set_freq to 0x46, EMMC_CKGEN_CTL=0x00002100, PLL_EMMC1=00000003, PLL_EMMC2=04517893, PLL_EMMC3=00464388, PLL_EMMC4=00000007
[ 3.226761] EMMC, set_ip_div = cur_div(0x00000080), ignored.
[ 3.229417] EMMC: set_freq to 0x46, EMMC_CKGEN_CTL=0x00002100, PLL_EMMC1=00000003, PLL_EMMC2=04517893, PLL_EMMC3=00464388, PLL_EMMC4=00000007
[ 3.229420] EMMC, set_ip_div = cur_div(0x00000080), ignored.
[ 3.235129] EMMC: set_freq to 0x46, EMMC_CKGEN_CTL=0x00002100, PLL_EMMC1=00000003, PLL_EMMC2=04517893, PLL_EMMC3=00464388, PLL_EMMC4=00000007
[ 3.235133] EMMC, set_ip_div = cur_div(0x00000080), ignored.
[ 3.235826] rtkemmc_set_rspparam : cmd7 arg : 0x00010000
[ 3.235828] rtkemmc_set_rspparam : cmd7 with rsp
[ 3.245472] xhci-hcd xhci-hcd.7.auto: RTK_phy_toggle to call RTK_dwc3_usb2_phy_toggle (wValue=10 port=0 status=202a0)
[ 3.245483] rtk-usb2phy 981f8280.dwc3_u3host_usb2phy: do_rtk_usb2_phy_toggle ########## to toggle Page1 addr 0xe0 BIT(2)
[ 3.246498] rtk-usb2phy 981f8280.dwc3_u3host_usb2phy: do_rtk_usb2_phy_toggle disconnect to set Page0 0xE7 = f1
[ 3.251699] card->mmc_avail_type = 0x00000013
[ 3.252947] EMMC: set_freq to 0x46, EMMC_CKGEN_CTL=0x00002100, PLL_EMMC1=00000003, PLL_EMMC2=04517893, PLL_EMMC3=00464388, PLL_EMMC4=00000007
[ 3.252951] EMMC, set_ip_div = cur_div(0x00000080), ignored.
[ 3.252953] set bus width 8
[ 3.252958] EMMC: set to 0x00010000, EMMC_CTYPE=00010000
[ 3.256335] EMMC: set_freq to 0xa6, EMMC_CKGEN_CTL=0x00002100, PLL_EMMC1=00000003, PLL_EMMC2=04517893, PLL_EMMC3=00a64388, PLL_EMMC4=00000007
[ 3.256347] EMMC: set div to 0x00, EMMC_CLKDIV=00000000
[ 3.256348] set bus width 8
[ 3.256353] EMMC: set to 0x00010000, EMMC_CTYPE=00010000
[ 3.256784] EMMC: set_freq to 0xa6, EMMC_CKGEN_CTL=0x00002100, PLL_EMMC1=00000003, PLL_EMMC2=04517893, PLL_EMMC3=00a64388, PLL_EMMC4=00000007
[ 3.256787] EMMC, set_ip_div = cur_div(0x00000000), ignored.
[ 3.256789] set bus width 8
[ 3.256794] EMMC: set to 0x00010000, EMMC_CTYPE=00010000
[ 3.256798] emmc card manid = 0x00000015
[ 3.256802] EMMC: set_wrapper_div to 0x00002100
[ 3.257231] EMMC: set_freq to 0xa6, EMMC_CKGEN_CTL=0x00002100, PLL_EMMC1=00000003, PLL_EMMC2=04517893, PLL_EMMC3=00a64388, PLL_EMMC4=00000007
[ 3.257234] EMMC, set_ip_div = cur_div(0x00000000), ignored.
[ 3.257448] Inherit bootcode tuning phase: TX=0x11, RX=0x17
[ 3.267454] HS200: final phase=0x178b
[ 3.269621] mmc0: new HS200 MMC card at address 0001
[ 3.270091] mmcblk0: mmc0:0001 8GTF4R 7.28 GiB
[ 3.270333] mmcblk0boot0: mmc0:0001 8GTF4R partition 1 4.00 MiB
[ 3.274572] mmcblk0boot1: mmc0:0001 8GTF4R partition 2 4.00 MiB
[ 3.278806] mmcblk0rpmb: mmc0:0001 8GTF4R partition 3 512 KiB
[ 3.279505] mmcblk0: p1 p2
[ 3.285423] mmc0: retry_left=46, block_dev=[16 -> 22], time=65ms
[ 3.285565] sdhci: Secure Digital Host Controller Interface driver
[ 3.285567] sdhci: Copyright(c) Pierre Ossman
[ 3.285569] sdhci-pltfm: SDHCI platform and OF driver helper
[ 3.285731] rtk-sdio: build at : #0 SMP PREEMPT Mon Apr 8 13:55:47 2024
[ 3.373427] [SDIO] SDHCI_SPEC_300: rtk_sdhci_set_clock end real_div=1f4, div=fa, c3c=0, PLL=ae4388, CLK=fa07
[ 3.393427] mmc1: SDHCI controller on 98010c00.sdio [98010c00.sdio] using ADMA
[ 3.393725] rtk_sdmmc_probe: clk_get() returns -2
[ 3.393745] rtk-sdmmc: build at : #0 SMP PREEMPT Mon Apr 8 13:55:47 2024
[ 3.393748] rtk-sdmmc: CONFIG_MMC_BLOCK_BOUNCE enable
[ 3.397680] rtk-sdio 98010c00.sdio: card claims to support voltages below defined range
[ 3.400361] SDIO 3.0 A01 version
[ 3.400363] SDIO SDR104 mode
[ 3.410913] [SDIO] SDHCI_SPEC_300: rtk_sdhci_set_clock end real_div=1, div=0, c3c=b0000, PLL=ae4388, CLK=7
[ 3.410921] rtk_sdhci_execute_tuning : Execute Clock Phase Tuning
[ 3.422538] rtk_sdhci_tuning_tx TX phase_map = 0xfe1fffff
[ 3.422543] rtk_sdhci_tuning_tx final phase = 0x00000007
[ 3.434659] rtk_sdhci_tuning_rx RX phase_map = 0x7ffc03ff
[ 3.434664] rtk_sdhci_tuning_rx final phase = 0x00000018
[ 3.434767] After tuning, current SDIO PLL = ae
[ 3.435024] random: fast init done
[ 3.435744] mmc1: new ultra high speed SDR104 SDIO card at address 0001
[ 3.458332] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 3.458588] rtk_sdmmc_get_cd: SD card does not exist, regCARD_EXIST = 20
[ 3.459367] [sound/arm/snd-realtek.c snd_card_create_PCM_instance 4172]
[ 3.459476] [sound/arm/snd-realtek.c snd_card_create_PCM_instance 4172]
[ 3.459514] [sound/arm/snd-realtek.c snd_card_create_PCM_instance 4172]
[ 3.459553] [sound/arm/snd-realtek.c snd_card_create_PCM_instance 4172]
[ 3.459594] [sound/arm/snd-realtek.c snd_card_create_PCM_instance 4172]
[ 3.459633] [sound/arm/snd-realtek.c snd_card_create_PCM_instance 4172]
[ 3.495159] NET: Registered protocol family 10
[ 3.513475] NET: Registered protocol family 17
[ 3.513541] 8021q: 802.1Q VLAN Support v1.8
[ 3.513566] Key type dns_resolver registered
[ 3.520117] Registered cp15_barrier emulation handler
[ 3.520127] Registered setend emulation handler
[ 3.520660] registered taskstats version 1
[ 3.523400] [RTK_SCPU_WRAPPER] scpu wrappee irq 25, scpu_wrap_addr 0xffffff80096da000
[ 3.523448] [RTK_SCPU_WRAPPER] initialized
[ 3.523450] [RTK_SCPU_WRAPPER] memory monitor 0x98013b00 - 0x98013c00
[ 3.524051] rtk-uctrl rtk-uctrl.0: initialized
[ 3.524261] rtk-ccsc rtk-ccsc: initialized
[ 3.524691] [RTK_RTC] 9801b600.rtc: setting system clock to 2016-01-01 11:29:49 UTC (1451647789)
[ 3.525688] audio-notifier audio-out-devices: rtk_audio_notifier_probe
[ 3.525712] audio-notifier audio-out-devices: i2s: mode=master, channel=2
[ 3.525831] clk_mmio_gate_disable_unused: clk_en_ur2
[ 3.525842] clk_mmio_gate_disable_unused: clk_en_misc_i2c_1
[ 3.525864] clk_mmio_gate_disable_unused: clk_en_nf
[ 3.525894] pll_ddsb: clk_pll_disable_unused
[ 3.525914] pctrl_gpu: rtk_sram_power_off_unused
[ 3.525927] ALSA device list:
[ 3.525930] #0: snd_alsa_rtk
[ 5.337949] ttyS0 - failed to request DMA
[ 5.344145] VFS: Mounted root (squashfs filesystem) readonly on device 179:1.
[ 5.356084] devtmpfs: mounted
[ 5.360512] Freeing unused kernel memory: 3392K
[ 5.822929] init: Console is alive
[ 6.294222] ahci_rtk 9803f000.sata: masking port_map 0x3 -> 0x3
[ 6.300377] ahci_rtk 9803f000.sata: AHCI 0001.0301 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 6.309489] ahci_rtk 9803f000.sata: flags: ncq sntf pm led clo only pmp fbs pio slum part ccc sadm sds apst
[ 6.322607] scsi host0: ahci_rtk
[ 6.326324] scsi host1: ahci_rtk
[ 6.329839] ata1: SATA max UDMA/133 mmio [mem 0x9803f000-0x9803ffff] port 0x100 irq 10
[ 6.337975] ata2: SATA max UDMA/133 mmio [mem 0x9803f000-0x9803ffff] port 0x180 irq 10
[ 6.553439] phy-rtk-sata 9803ff00.sata_phy: power on phy1
[ 6.559014] phy-rtk-sata 9803ff00.sata_phy: power on phy0
[ 6.665927] ata2: SATA link down (SStatus 0 SControl 300)
[ 6.678077] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.773485] raid6: int64x1 gen() 267 MB/s
[ 6.845489] raid6: int64x1 xor() 241 MB/s
[ 6.917428] raid6: int64x2 gen() 431 MB/s
[ 6.989419] raid6: int64x2 xor() 366 MB/s
[ 7.061416] raid6: int64x4 gen() 605 MB/s
[ 7.133417] raid6: int64x4 xor() 437 MB/s
[ 7.205482] raid6: int64x8 gen() 491 MB/s
[ 7.277459] raid6: int64x8 xor() 401 MB/s
[ 7.349518] raid6: neonx1 gen() 478 MB/s
[ 7.421429] raid6: neonx1 xor() 472 MB/s
[ 7.493447] raid6: neonx2 gen() 729 MB/s
[ 7.565403] raid6: neonx2 xor() 639 MB/s
[ 7.637459] raid6: neonx4 gen() 990 MB/s
[ 7.709438] raid6: neonx4 xor() 755 MB/s
[ 7.781422] raid6: neonx8 gen() 991 MB/s
[ 7.853428] raid6: neonx8 xor() 755 MB/s
[ 7.857815] raid6: using algorithm neonx8 gen() 991 MB/s
[ 7.863265] raid6: .... xor() 755 MB/s, rmw enabled
[ 7.868271] raid6: using intx1 recovery algorithm
[ 7.873599] xor: measuring software checksum speed
[ 7.917398] 8regs : 1437.000 MB/sec
[ 7.961417] 8regs_prefetch: 1288.000 MB/sec
[ 8.005398] 32regs : 1868.000 MB/sec
[ 8.049399] 32regs_prefetch: 1627.000 MB/sec
[ 8.054140] xor: using function: 32regs (1868.000 MB/sec)
[ 8.261770] Btrfs loaded, crc32c=crc32c-arm64-hw
[ 8.272315] exFAT: Version 1.2.9
[ 8.525138] SGI XFS with ACLs, security attributes, no debug enabled
[ 8.535187] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 8.551916] init: - preinit -
[ 9.099388] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.121790] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.134316] Starting lvm2 during preinit
[ 9.690051] random: lvm: uninitialized urandom read (4 bytes read)
[ 10.617052] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 10.663504] urandom-seed: Seeding with /etc/urandom.seed
[ 10.724155] procd: - early -
[ 11.360222] procd: - ubus -
[ 11.416800] urandom_read: 1 callbacks suppressed
[ 11.416805] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.428310] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.434858] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.441868] procd: - init -
[ 11.595858] write procfs ethernet wol_enable = 1
[ 11.676703] kmodloader: loading kernel modules from /etc/modules.d/*
[ 11.729169] md: linear personality registered for level -1
[ 11.735730] md: raid0 personality registered for level 0
[ 11.737418] ata1: link is slow to respond, please be patient (ready=0)
[ 11.750256] md: raid1 personality registered for level 1
[ 11.758476] md: raid10 personality registered for level 10
[ 11.764683] async_tx: api initialized (async)
[ 11.778290] md: raid6 personality registered for level 6
[ 11.783759] md: raid5 personality registered for level 5
[ 11.789245] md: raid4 personality registered for level 4
[ 11.795715] md: multipath personality registered for level -4
[ 11.820256] tun: Universal TUN/TAP device driver, 1.6
[ 11.825462] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 11.835458] gre: GRE over IPv4 demultiplexor driver
[ 11.841629] ip_gre: GRE over IPv4 tunneling driver
[ 11.881017] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 11.894602] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 11.906181] cryptodev: driver 1.9 loaded.
[ 11.911258] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[ 11.919484] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[ 12.035449] fuse init (API version 7.26)
[ 12.557307] RTW: module init start
[ 12.560823] RTW: rtl8812au v5.2.20.2_28373.20180619_v0.17_20181026
[ 12.567167] RTW: build time: Apr 8 2024 13:55:47
[ 12.572132] usbcore: registered new interface driver rtl8812au
[ 12.578124] RTW: module init ret=0
[ 13.123488] RTW: module init start
[ 13.127005] RTW: rtl8821cu v5.4.1_28754.20180921_COEX20180712-3232_v0.14_20190516
[ 13.134724] RTW: build time: Apr 8 2024 13:55:47
[ 13.139556] RTW: rtl8821cu BT-Coex version = COEX20180712-3232
[ 13.145673] usbcore: registered new interface driver rtl8821cu
[ 13.151664] RTW: module init ret=0
[ 13.752254] RTW: module init start
[ 13.755772] RTW: rtl88x2cs v5.12.1.1-0-gf673ce3.20210125_COEX20200922-1e1e
[ 13.762825] RTW: build time: Apr 8 2024 13:55:47
[ 13.767656] RTW: rtl88x2cs BT-Coex version = COEX20200922-1e1e
[ 13.773995] RTW: == SDIO Card Info ==
[ 13.777771] RTW: card: ffffffc07a8bb800
[ 13.781891] RTW: clock: 200000000 Hz
[ 13.785743] RTW: timing spec: sd uhs SDR104
[ 13.790243] RTW: sd3_bus_mode: TRUE
[ 13.794005] RTW: func num: 1
[ 13.797135] RTW: func1: ffffffc07a857800 (*)
[ 13.801697] RTW: ================
[ 13.805309] RTW: [HALMAC]55772M
[ 13.805309] HALMAC_MAJOR_VER = 1
[ 13.805309] HALMAC_PROTOTYPE_VER = 6
[ 13.805309] HALMAC_MINOR_VER = 6
[ 13.805309] HALMAC_PATCH_VER = 22
[ 13.866439] RTW: HW EFUSE
[ 13.869152] RTW: 0x000: 29 81 00 8F FF 20 28 00 9A 04 ED 75 10 0F F1 EB
[ 13.876640] RTW: 0x010: 4D 4D 4F 4F 4F 4F 40 40 42 42 42 04 00 00 FF FF
[ 13.884122] RTW: 0x020: FF FF 3F 3C 40 40 39 39 39 3A 3C 36 37 38 39 40
[ 13.891599] RTW: 0x030: 04 00 FF FF 00 FF 00 00 FF FF 53 53 56 5A 5A 5A
[ 13.899078] RTW: 0x040: 45 45 48 4C 4C 04 00 00 FF FF FF FF 42 44 41 43
[ 13.906594] RTW: 0x050: 3B 3A 3D 41 41 42 3E 40 40 3F 04 00 FF FF 00 FF
[ 13.914075] RTW: 0x060: 00 00 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.921552] RTW: 0x070: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.929024] RTW: 0x080: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.936501] RTW: 0x090: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.943979] RTW: 0x0A0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.951457] RTW: 0x0B0: FF FF FF FF FF FF FF FF 7F 45 FF 00 FF FF FF FF
[ 13.958937] RTW: 0x0C0: FF 21 00 10 00 00 FF FF 00 33 04 FF FF FF FF FF
[ 13.966441] RTW: 0x0D0: 1C 20 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.973921] RTW: 0x0E0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.981399] RTW: 0x0F0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 13.988868] RTW: 0x100: F0 94 65 D3 58 C5 FF FF CD F0 FF FF FF FF FF FF
[ 13.996343] RTW: 0x110: 45 45 FC A0 D8 D8 FD FF 35 8C FF FF FF FF FF FF
[ 14.003820] RTW: 0x120: FE DF 01 23 34 FF FF FF FF FF 4C 02 22 C8 FF FF
[ 14.011298] RTW: 0x130: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 14.018803] RTW: 0x140: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 14.026289] RTW: 0x150: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 14.033779] RTW: 0x160: FF FF FF FF FF FF FF FF FF FF F0 B0 40 6F B9 F9
[ 14.041254] RTW: 0x170: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 14.048750] RTW: 0x180: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 14.056231] RTW: 0x190: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 14.063711] RTW: 0x1A0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 14.071191] RTW: 0x1B0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 14.078713] RTW: 0x1C0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 14.086196] RTW: 0x1D0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 14.093674] RTW: 0x1E0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 14.101140] RTW: 0x1F0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 14.108619] RTW: 0x200: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 14.116094] RTW: 0x210: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 14.123579] RTW: 0x220: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 14.131086] RTW: 0x230: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 14.138568] RTW: 0x240: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 14.146045] RTW: 0x250: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 14.153523] RTW: 0x260: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 14.160990] RTW: 0x270: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 14.168470] RTW: 0x280: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 14.175948] RTW: 0x290: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 14.183423] RTW: 0x2A0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 14.190929] RTW: 0x2B0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 14.198408] RTW: 0x2C0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 14.205884] RTW: 0x2D0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 14.213351] RTW: 0x2E0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 14.220833] RTW: 0x2F0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 14.228323] RTW: hal_com_config_channel_plan chplan:0x7F
[ 14.257760] RTW: WARN Invalid rate 0x0 in MRateToHwRate
[ 14.263149] RTW: WARN Invalid rate 0x0 in MRateToHwRate
[ 14.268521] RTW: WARN Invalid rate 0x0 in MRateToHwRate
[ 14.288600] RTW: [RF_PATH] ver_id.RF_TYPE:RF_2T2R
[ 14.293441] RTW: [RF_PATH] HALSPEC's rf_reg_trx_path_bmp:0x33, rf_reg_path_avail_num:2, max_tx_cnt:2
[ 14.302831] RTW: [RF_PATH] PG's trx_path_bmp:0x33, max_tx_cnt:0
[ 14.308911] RTW: [RF_PATH] Registry's trx_path_bmp:0x00, tx_path_lmt:0, rx_path_lmt:0
[ 14.316943] RTW: [RF_PATH] HALDATA's trx_path_bmp:0x33, max_tx_cnt:2
[ 14.323462] RTW: [RF_PATH] HALDATA's rf_type:RF_2T2R, NumTotalRFPath:2
[ 14.330161] RTW: [TRX_Nss] HALSPEC - tx_nss:2, rx_nss:2
[ 14.335524] RTW: [TRX_Nss] Registry - tx_nss:0, rx_nss:0
[ 14.340977] RTW: [TRX_Nss] HALDATA - tx_nss:2, rx_nss:2
[ 14.346343] RTW: txpath=0x3, rxpath=0x3
[ 14.350285] RTW: txpath_1ss:0x1, num:1
[ 14.354136] RTW: txpath_2ss:0x3, num:2
[ 14.358619] RTW: rtw_regsty_chk_target_tx_power_valid return _FALSE for band:0, path:0, rs:0, t:-1
[ 14.372131] RTW: rtw_ndev_init(wlan0) if1 mac_addr=f0:b0:40:6f:b9:f9
[ 14.379827] RTW: rtw_ndev_init(wlan1) if2 mac_addr=f2:b0:40:6f:b9:f9
[ 14.387541] RTW: module init ret=0
[ 14.394207] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 14.409634] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 14.571612] xt_time: kernel timezone is -0000
[ 14.581608] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 16.377464] ata1: COMRESET failed (errno=-16)
[ 16.572082] r8169 98016000.gmac eth0: rtl_csiar_cond == 0 (loop: 100, delay: 10).
[ 16.581163] r8169 98016000.gmac eth0: rtl_csiar_cond == 1 (loop: 100, delay: 10).
[ 16.590133] r8169 98016000.gmac eth0: link down
[ 16.594967] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 16.601980] r8169 98016000.gmac eth0: link down
[ 19.097222] r8169 98016000.gmac eth0: link up
[ 19.101774] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 19.122614] r8169 98016000.gmac eth0: rtl_csiar_cond == 0 (loop: 100, delay: 10).
[ 19.131587] r8169 98016000.gmac eth0: rtl_csiar_cond == 1 (loop: 100, delay: 10).
[ 19.140574] r8169 98016000.gmac eth0: link up
[ 21.737431] ata1: link is slow to respond, please be patient (ready=0)
[ 23.549465] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 23.560271] ata1.00: ATA-10: ST6000NM0024-1HT17Z, MA29, max UDMA/133
[ 23.567199] ata1.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 23.575043] ata1.00: configured for UDMA/133
[ 23.579992] scsi 0:0:0:0: Direct-Access ATA ST6000NM0024-1HT MA29 PQ: 0 ANSI: 5
[ 23.638322] sd 0:0:0:0: [sda] 11721045168 512-byte logical blocks: (6.00 TB/5.46 TiB)
[ 23.646378] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 23.651973] sd 0:0:0:0: [sda] Write Protect is off
[ 23.656926] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 23.662206] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 23.714322] sda: sda1
[ 23.717979] sd 0:0:0:0: [sda] Attached SCSI disk
[ 37.491454] ---mv crash logs:1 to mmc
[ 37.511117] start ug_sys_log server
[ 37.974563] start ug_sys_log_monitor server
[ 38.998864] random: crng init done
[ 39.002363] random: 3 urandom warning(s) missed due to ratelimiting
[ 40.002265] ---ug_sys_log_monitor.sh sleep 10,before uptime 60 second
[ 40.359912] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 40.367986] NFSD: starting 90-second grace period (net ffffff800921e700)
[ 40.870464] md: md0 stopped.
[ 40.912232] md: bind<sda1>
[ 40.919827] md/raid1:md0: active with 1 out of 2 mirrors
[ 40.926928] created bitmap (44 pages) for device md0
[ 40.940262] md0: bitmap initialized from disk: read 3 pages, set 63 of 89423 bits
[ 40.954809] md0: detected capacity change from 0 to 6001039245312
[ 42.632937] aria2. start copy,Sat Feb 1 09:33:21 CST 2025
[ 42.638943] /data/.ugreen_nas/conf/
[ 42.659087] drwxrwxrwx 6 root root 4096 Feb 1 09:26 conf
[ 42.659087] drwxrwxrwx 3 root root 4096 Dec 9 2023 db
[ 42.659087] drwxrwxrwx 2 root root 4096 Jan 1 2021 log
[ 42.659087] drwxrwxrwx 2 root root 4096 Jan 1 2021 task_manager
[ 42.659087] drwxrwxrwx 5 root root 4096 Oct 24 2022 upgrade_dir
[ 42.695755] break
[ 42.702917] aria2. end copy,Sat Feb 1 09:33:21 CST 2025
[ 42.760413] begin syncthing config: Sat Feb 1 09:33:21 CST 2025
[ 43.014642] WARNING: Key exists; will not overwrite.
[ 43.019928] Device ID: 44YUUVD-2B572F6-VOWIMSA-JH226BS-F6FMTNB-V2FXYQM-35O7ZWB-L36SDQA
[ 43.062430] -rw-r--r-- 1 daemon daemon 794 May 29 2022 cert.pem
[ 43.062430] -rw------- 1 root root 8973 Feb 1 09:33 config.xml
[ 43.062430] -rw------- 1 daemon daemon 825 May 29 2022 csrftokens.txt
[ 43.062430] -rw-r--r-- 1 daemon daemon 802 Aug 11 17:32 https-cert.pem
[ 43.062430] -rw------- 1 daemon daemon 288 Aug 11 17:32 https-key.pem
[ 43.062430] drwxr-xr-x 2 daemon daemon 4096 Feb 1 09:23 index-v0.14.0.db
[ 43.062430] -rw------- 1 daemon daemon 288 May 29 2022 key.pem
[ 43.128100] userInfoExist: 1
[ 43.135405] EXT4-fs (md0): barriers disabled
[ 43.136772] <address>dynamic</address>
[ 43.136772] <address>dynamic</address>
[ 43.136772] <address>dynamic</address>
[ 43.136772] <address>dynamic</address>
[ 43.136772] <address>127.0.0.1:8394</address>
[ 43.136772] <user>ugreennasworkbench</user>
[ 43.136772] <password>$2a$10$Atv1ZeiWIJ2uSZdS9WUEt.6Jx6PWbQ.N7n6BL1BQ7jibRDszVKHOy</password>
[ 43.136772] <address>dynamic</address>
[ 43.137655] edit
[ 43.155295] end syncthing config: Sat Feb 1 09:33:21 CST 2025
[ 43.161197] <address>dynamic</address>
[ 43.161197] <address>dynamic</address>
[ 43.161197] <address>dynamic</address>
[ 43.161197] <address>dynamic</address>
[ 43.161197] <address>127.0.0.1:8394</address>
[ 43.161197] <user>ugreennasworkbench</user>
[ 43.161197] <password>$2a$10$Atv1ZeiWIJ2uSZdS9WUEt.6Jx6PWbQ.N7n6BL1BQ7jibRDszVKHOy</password>
[ 43.161197] <address>dynamic</address>
[ 45.904723] EXT4-fs (md0): recovery complete
[ 45.944460] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: nobarrier,usrquota,grpquota,prjquota
[ 46.620344] Adding 2097148k swap on /mnt/md0/.swapfile. Priority:-1 extents:2 across:2228220k
[ 50.029964] ---ug_sys_log_monitor.sh sleep 10,before uptime 60 second
[ 54.131716] [RTK_VE1] before pctrl_on for laterncy watching!!
[ 54.137728] [RTK_VE1] after pctrl_on for laterncy watching!!
[ 54.429802] [RTK_VE1] before pctrl_on for laterncy watching!!
[ 54.438323] [RTK_VE1] after pctrl_on for laterncy watching!!
[ 56.151855] xunlei-pan-cli is runing!,Sat Feb 1 09:33:34 CST 2025
[ 60.064886] ---ug_sys_log_monitor.sh sleep 10,before uptime 60 second
[ 70.096454] ---SYS_LOG_FILE:/data/nas_server/log/system/HB316F032200FEBC_20250201093316_syslog
root@UGREEN-38CA:~# free -h
total used free shared buff/cache available
Mem: 1.5G 407M 142M 5.7M 1.0G 782M
Swap: 2.0G 1.4M 2.0G
root@UGREEN-38CA:~# cd /data/nas_server/log/system/
root@UGREEN-38CA:/data/nas_server/log/system# ll
drwxrwxrwx 3 root root 4096 Feb 1 09:33 ./
drwxrwxrwx 5 root root 61440 Feb 1 09:32 ../
-rwxrwxrwx 1 root root 105372 Jan 31 22:24 HB316F032200FEBC_20250131222346_syslog*
-rwxrwxrwx 1 root root 80533 Jan 31 22:27 HB316F032200FEBC_20250131222637_syslog*
-rwxrwxrwx 1 root root 205127 Feb 1 08:45 HB316F032200FEBC_20250131222811_syslog*
-rwxrwxrwx 1 root root 109337 Feb 1 08:48 HB316F032200FEBC_20250201084617_syslog*
-rwxrwxrwx 1 root root 105090 Feb 1 08:54 HB316F032200FEBC_20250201085252_syslog*
-rwxrwxrwx 1 root root 113213 Feb 1 09:32 HB316F032200FEBC_20250201092302_syslog*
-rwxrwxrwx 1 root root 109949 Feb 1 09:33 HB316F032200FEBC_20250201093316_syslog*
drwxrwxrwx 3 root root 4096 Feb 1 09:33 crash/
root@UGREEN-38CA:/data/nas_server/log/system# ll^C
root@UGREEN-38CA:/data/nas_server/log/system# ^C
root@UGREEN-38CA:/data/nas_server/log/system# ^C
root@UGREEN-38CA:/data/nas_server/log/system# ^C
root@UGREEN-38CA:/data/nas_server/log/system# grep -inr -A 15 "lsblk" ./*.
grep: ./*.: No such file or directory
root@UGREEN-38CA:/data/nas_server/log/system# grep -inr -A 15 "lsblk" ./*
./HB316F032200FEBC_20250131222346_syslog:1114:-------------------lsblk:
./HB316F032200FEBC_20250131222346_syslog-1115-NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
./HB316F032200FEBC_20250131222346_syslog-1116-mmcblk0 179:0 0 7.3G 0 disk
./HB316F032200FEBC_20250131222346_syslog-1117-|-mmcblk0p1 179:1 0 1G 0 part /rom
./HB316F032200FEBC_20250131222346_syslog-1118-`-mmcblk0p2 179:2 0 5.2G 0 part /overlay
./HB316F032200FEBC_20250131222346_syslog-1119-mmcblk0boot0 179:8 0 4M 1 disk
./HB316F032200FEBC_20250131222346_syslog-1120-mmcblk0boot1 179:16 0 4M 1 disk
./HB316F032200FEBC_20250131222346_syslog-1121-mmcblk0rpmb 179:24 0 512K 0 disk
./HB316F032200FEBC_20250131222346_syslog-1122--------------------route -n:
./HB316F032200FEBC_20250131222346_syslog-1123-Kernel IP routing table
./HB316F032200FEBC_20250131222346_syslog-1124-Destination Gateway Genmask Flags Metric Ref Use Iface
./HB316F032200FEBC_20250131222346_syslog-1125-0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth0
./HB316F032200FEBC_20250131222346_syslog-1126-192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
./HB316F032200FEBC_20250131222346_syslog-1127--------------------ifconfig -a:
./HB316F032200FEBC_20250131222346_syslog-1128-bond0 Link encap:Ethernet HWaddr 92:FC:32:2A:44:17
./HB316F032200FEBC_20250131222346_syslog-1129- BROADCAST MASTER MULTICAST MTU:1500 Metric:1
--
./HB316F032200FEBC_20250131222811_syslog:1122:-------------------lsblk:
./HB316F032200FEBC_20250131222811_syslog-1123-NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
./HB316F032200FEBC_20250131222811_syslog-1124-sda 8:0 0 5.5T 0 disk
./HB316F032200FEBC_20250131222811_syslog-1125-`-sda1 8:1 0 5.5T 0 part
./HB316F032200FEBC_20250131222811_syslog-1126- `-md0 9:0 0 5.5T 0 raid1 /mnt/md0
./HB316F032200FEBC_20250131222811_syslog-1127-mmcblk0 179:0 0 7.3G 0 disk
./HB316F032200FEBC_20250131222811_syslog-1128-|-mmcblk0p1 179:1 0 1G 0 part /rom
./HB316F032200FEBC_20250131222811_syslog-1129-`-mmcblk0p2 179:2 0 5.2G 0 part /overlay
./HB316F032200FEBC_20250131222811_syslog-1130-mmcblk0boot0 179:8 0 4M 1 disk
./HB316F032200FEBC_20250131222811_syslog-1131-mmcblk0boot1 179:16 0 4M 1 disk
./HB316F032200FEBC_20250131222811_syslog-1132-mmcblk0rpmb 179:24 0 512K 0 disk
./HB316F032200FEBC_20250131222811_syslog-1133--------------------route -n:
./HB316F032200FEBC_20250131222811_syslog-1134-Kernel IP routing table
./HB316F032200FEBC_20250131222811_syslog-1135-Destination Gateway Genmask Flags Metric Ref Use Iface
./HB316F032200FEBC_20250131222811_syslog-1136-0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth0
./HB316F032200FEBC_20250131222811_syslog-1137-192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
--
./HB316F032200FEBC_20250201084617_syslog:1147:-------------------lsblk:
./HB316F032200FEBC_20250201084617_syslog-1148-NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
./HB316F032200FEBC_20250201084617_syslog-1149-sda 8:0 0 5.5T 0 disk
./HB316F032200FEBC_20250201084617_syslog-1150-`-sda1 8:1 0 5.5T 0 part
./HB316F032200FEBC_20250201084617_syslog-1151- `-md0 9:0 0 5.5T 0 raid1 /mnt/md0
./HB316F032200FEBC_20250201084617_syslog-1152-mmcblk0 179:0 0 7.3G 0 disk
./HB316F032200FEBC_20250201084617_syslog-1153-|-mmcblk0p1 179:1 0 1G 0 part /rom
./HB316F032200FEBC_20250201084617_syslog-1154-`-mmcblk0p2 179:2 0 5.2G 0 part /overlay
./HB316F032200FEBC_20250201084617_syslog-1155-mmcblk0boot0 179:8 0 4M 1 disk
./HB316F032200FEBC_20250201084617_syslog-1156-mmcblk0boot1 179:16 0 4M 1 disk
./HB316F032200FEBC_20250201084617_syslog-1157-mmcblk0rpmb 179:24 0 512K 0 disk
./HB316F032200FEBC_20250201084617_syslog-1158--------------------route -n:
./HB316F032200FEBC_20250201084617_syslog-1159-Kernel IP routing table
./HB316F032200FEBC_20250201084617_syslog-1160-Destination Gateway Genmask Flags Metric Ref Use Iface
./HB316F032200FEBC_20250201084617_syslog-1161-0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth0
./HB316F032200FEBC_20250201084617_syslog-1162-192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
--
./HB316F032200FEBC_20250201085252_syslog:1115:-------------------lsblk:
./HB316F032200FEBC_20250201085252_syslog-1116-NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
./HB316F032200FEBC_20250201085252_syslog-1117-sda 8:0 0 5.5T 0 disk
./HB316F032200FEBC_20250201085252_syslog-1118-`-sda1 8:1 0 5.5T 0 part
./HB316F032200FEBC_20250201085252_syslog-1119- `-md0 9:0 0 5.5T 0 raid1 /mnt/md0
./HB316F032200FEBC_20250201085252_syslog-1120-mmcblk0 179:0 0 7.3G 0 disk
./HB316F032200FEBC_20250201085252_syslog-1121-|-mmcblk0p1 179:1 0 1G 0 part /rom
./HB316F032200FEBC_20250201085252_syslog-1122-`-mmcblk0p2 179:2 0 5.2G 0 part /overlay
./HB316F032200FEBC_20250201085252_syslog-1123-mmcblk0boot0 179:8 0 4M 1 disk
./HB316F032200FEBC_20250201085252_syslog-1124-mmcblk0boot1 179:16 0 4M 1 disk
./HB316F032200FEBC_20250201085252_syslog-1125-mmcblk0rpmb 179:24 0 512K 0 disk
./HB316F032200FEBC_20250201085252_syslog-1126--------------------route -n:
./HB316F032200FEBC_20250201085252_syslog-1127-Kernel IP routing table
./HB316F032200FEBC_20250201085252_syslog-1128-Destination Gateway Genmask Flags Metric Ref Use Iface
./HB316F032200FEBC_20250201085252_syslog-1129-0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth0
./HB316F032200FEBC_20250201085252_syslog-1130-192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
--
./HB316F032200FEBC_20250201092302_syslog:1132:-------------------lsblk:
./HB316F032200FEBC_20250201092302_syslog-1133-NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
./HB316F032200FEBC_20250201092302_syslog-1134-sda 8:0 0 5.5T 0 disk
./HB316F032200FEBC_20250201092302_syslog-1135-`-sda1 8:1 0 5.5T 0 part
./HB316F032200FEBC_20250201092302_syslog-1136- `-md0 9:0 0 5.5T 0 raid1 /mnt/md0
./HB316F032200FEBC_20250201092302_syslog-1137-mmcblk0 179:0 0 7.3G 0 disk
./HB316F032200FEBC_20250201092302_syslog-1138-|-mmcblk0p1 179:1 0 1G 0 part /rom
./HB316F032200FEBC_20250201092302_syslog-1139-`-mmcblk0p2 179:2 0 5.2G 0 part /overlay
./HB316F032200FEBC_20250201092302_syslog-1140-mmcblk0boot0 179:8 0 4M 1 disk
./HB316F032200FEBC_20250201092302_syslog-1141-mmcblk0boot1 179:16 0 4M 1 disk
./HB316F032200FEBC_20250201092302_syslog-1142-mmcblk0rpmb 179:24 0 512K 0 disk
./HB316F032200FEBC_20250201092302_syslog-1143--------------------route -n:
./HB316F032200FEBC_20250201092302_syslog-1144-Kernel IP routing table
./HB316F032200FEBC_20250201092302_syslog-1145-Destination Gateway Genmask Flags Metric Ref Use Iface
./HB316F032200FEBC_20250201092302_syslog-1146-0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth0
./HB316F032200FEBC_20250201092302_syslog-1147-192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
--
./HB316F032200FEBC_20250201093316_syslog:1151:-------------------lsblk:
./HB316F032200FEBC_20250201093316_syslog-1152-NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
./HB316F032200FEBC_20250201093316_syslog-1153-sda 8:0 0 5.5T 0 disk
./HB316F032200FEBC_20250201093316_syslog-1154-`-sda1 8:1 0 5.5T 0 part
./HB316F032200FEBC_20250201093316_syslog-1155- `-md0 9:0 0 5.5T 0 raid1 /mnt/md0
./HB316F032200FEBC_20250201093316_syslog-1156-mmcblk0 179:0 0 7.3G 0 disk
./HB316F032200FEBC_20250201093316_syslog-1157-|-mmcblk0p1 179:1 0 1G 0 part /rom
./HB316F032200FEBC_20250201093316_syslog-1158-`-mmcblk0p2 179:2 0 5.2G 0 part /overlay
./HB316F032200FEBC_20250201093316_syslog-1159-mmcblk0boot0 179:8 0 4M 1 disk
./HB316F032200FEBC_20250201093316_syslog-1160-mmcblk0boot1 179:16 0 4M 1 disk
./HB316F032200FEBC_20250201093316_syslog-1161-mmcblk0rpmb 179:24 0 512K 0 disk
./HB316F032200FEBC_20250201093316_syslog-1162--------------------route -n:
./HB316F032200FEBC_20250201093316_syslog-1163-Kernel IP routing table
./HB316F032200FEBC_20250201093316_syslog-1164-Destination Gateway Genmask Flags Metric Ref Use Iface
./HB316F032200FEBC_20250201093316_syslog-1165-0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth0
./HB316F032200FEBC_20250201093316_syslog-1166-192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
root@UGREEN-38CA:/data/nas_server/log/system# client_loop: send disconnect: Connection reset
C:\Users\Administrator>ssh -p 922 root@192.168.2.150
C:\Users\Administrator>
C:\Users\Administrator>
C:\Users\Administrator>
C:\Users\Administrator>
C:\Users\Administrator>
C:\Users\Administrator>
C:\Users\Administrator>
C:\Users\Administrator>
C:\Users\Administrator>ping 192.168.2.158
Pinging 192.168.2.158 with 32 bytes of data:
Reply from 192.168.2.203: Destination host unreachable.
Reply from 192.168.2.203: Destination host unreachable.
Reply from 192.168.2.203: Destination host unreachable.
Reply from 192.168.2.203: Destination host unreachable.
Ping statistics for 192.168.2.158:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
C:\Users\Administrator>
最终排查发现两块硬盘没问题，是电源供电不足造成的。
果然，换了电源就能正常启动了。
乐果 发表于 2025 年 02 月 01 日 标签：openwrt